Bay Networks 58000 Installation And Reference Manual Download Page 129

Page: 129 / 158

Using the System Configuration Menus

893-878-B

6-23

Modifying Switch Port Type

To modify the switch port type, follow these steps:

Choose Configuration Parameters from the Main Menu.

The Configuration Parameters menu is displayed.

Choose Switch Parameters from the Configuration Parameters menu.

The Switch Parameters menu is displayed.

Choose Modify Switch Port Type from the Switch Parameters menu.

A Switch Port Type menu similar to that shown in

Figure 6-11

displayed.

Figure 6-11. Switch Port Type menu

Bay Networks 58000 Ethernet Switch Model

System Up Time: 1 D-12H-22M-11S IP Address: 134.177.32.98(M)

MAC Address: 000081000201 Default Gateway: 134.177.32.1

Switch Software Version: 1.4.3 Subnet Mask: 255.255.255.0

Switch Port Type

Port Operational Current Next Boot Port Operational Current Next Boot

1 [Act Feeder] [Auto] [Auto]

10 [Act Feeder] [Auto] [Auto]

2 [Act Feeder] [Auto] [Auto] 11 [Act Feeder] [Auto] [Auto]

3 [Act Feeder] [Auto] [Auto] 12 [Act Feeder] [Auto] [Auto]

4 [Act Feeder] [Auto] [Auto] 13 [Act Feeder] [Auto] [Auto]

5 [Act Feeder] [Auto] [Auto] 14 [Act Feeder] [Auto] [Auto]

6 [Act Feeder] [Auto] [Auto] 15 [Act Feeder] [Auto] [Auto]

7 [Act Feeder] [Auto] [Auto] 16 [Act Feeder] [Auto] [Auto]

8 [Act Feeder] [Auto] [Auto] MDA P1 [Act Feeder] [Auto] [Auto]

9 [Act Feeder] [Auto] [Auto] MDA P2 [Act Feeder] [Auto] [Auto]

Change port type of port 1.

Use cursor keys to choose item. Press <RETURN> to confirm choice.

<CTRL><P>: Main Menu <CTRL><U>: Previous Menu <CTRL><L>: Refresh Screen

893-878-B Book Page 23 Monday, May 12, 1997 2:06 PM

Summary of Contents for 58000































































































































































Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands

Bay Networks 58000, Installation And Reference Manual

Search results

Summary of Contents for 58000

Reviews:

Related manuals for 58000

Brands by name

Popular brands