manualshive.com logo in svg

baxter SP600 Series, Operation & Installation Manual, Page: 10 / 20

Share
Download
baxter SP600 Series Operation & Installation Manual Download Page 10

– 10 –

OPERATION

ENVIRONMENTAL CONDITIONS

•  Indoor use at altitudes up to 6,500 ft. (2,000 m).

•  Main supply voltage 

fl

 uctuations up to +/-10% of nominal voltage.

•  Installation category III, pollution degree II.

•  The normal ambient operating temperature is between 41°F (5°C) and 105°F (40°C). The normal 

operating water temperature is between 32°F (0°C) and 125°F (52°C).

CONTROLS

Hand Held Temperature Probe

The temperature window displays the temperature recorded by the hand held probe. The probe measures 
the temperature of the room, dough or 

fl

 our. The temperature range is 32°F

 

to 125°F (0°C to 52°C).

Water Temperature

SETTING window - Displays the water temperature as the water meter is dispensing. It  also displays the 
selected water temperature when the meter is idle.

FULL COLD light

 

- Indicates the mixing valve is using cold water only.

ADJUSTING light

 

- Indicates the mixing valve is adjusting the water temperature.

FULL HOT light

 

-

 

Indicates the mixing valve is using hot water only.

Summary of Contents for SP600 Series





















Reviews:

No comments