Baxi PREMIER PLUS 400 Installation And User Instructions Manual Download

Page: 14 / 16

12. SPARE PARTS

12.1 The following list of spare parts is available for the

BAXI Premier Plus water heater

. Refer to the

technical data label on the water heater to identify the model installed and to ensure the correct
parts are ordered.

12.2 DO NOT replace with parts not recommended by the manufacturer as this will invalidate your

guarantee and may render the installation dangerous.

Description

Part no.

3kW Immersion heater (1 3/4” screw thread)

95:602:030

3/4” Temperature/pressure relief valve

95:605:103

13. ENVIRONMENTAL INFORMATION

13.1 This water heater is manufactured from many recyclable materials. At the end of its useful life it

should be disposed of at an approved Recycling Centre to realise the full environmental benefits.

13.2 The insulation material is CFC/HCFC free expanded polyurethane foam with an ozone depletion

factor of zero.

Summary of Contents for PREMIER PLUS 400

















Search results

Summary of Contents for PREMIER PLUS 400

Reviews:

Related manuals for PREMIER PLUS 400

Brands by name

Popular brands

Baxi PREMIER PLUS 400, Installation And User Instructions Manual

Search results

Summary of Contents for PREMIER PLUS 400

Reviews:

Related manuals for PREMIER PLUS 400

Brands by name

Popular brands