background image

Supplied By www.heating spares.co  Tel. 0161 620 6677

Ebony Super

Baxi Heating Ltd.

page 3

Appliance Details – Page 3

Dimensions
HEIGHT
WIDTH
DEPTH

INPUT

OUTPUT

SETTING PRESSURE
(COLD)

GAS
ELECTRICAL
(MAIN INPUT)

THERMOCOUPLE
(OUTPUT)
RESISTOR
BURNER
PILOT IGNITION

WEIGHT

Projection in room
706mm (27 13/16 in)
750mm (29 ½ in)
326mm (12 13/16 in)

High - 5.42kW (18,500 Btu/h)
Low - 2.10kW (7,200Btu/h)
High - 3.47kW (11,840 Btu/h)

14.1 mbar± 1.0mbar
5.6in w.g. ± 0.4in w.g.

Natural Gas
230 volts ~ 50 Hz - 3A - 120W

9.4 to 13mV
68 ohms
Aerated - Duplex
Piezo Unit - Spark Gap
2.5mm - 4.0mm

40kg (88 lbs)

B.S. CODES OF PRACTICE

HEIGHT FROM HEARTH TO TOP OF FLUE SPIGOT

BS 6891

Gas Installation

489mm (19 ¼ in)

BS 5871 :Part 1

Installation of Gas Fires,
Convectors and Fire/Back Boilers

TAP

Duplex with rotary piezo

BS 5440:Part 1

Flues

and flame failure device

BS 5440:Part 2

Air Supply

operated by Oxy-pilot

BS 5258:Part 5

Fire Construction

BS 6332:Part 2

Fire Efficiency

BURNER INJECTORS

230

ELECTRICAL CONNECTION

THIS APPLIANCE MUST BE EARTHED

ALL EXTERNAL WIRING BETWEEN THE APPLIANCE AND
THE ELECTRICAL SUPPLY SHALL COMPLY WITH
CURRENT I.E.E. REGULATIONS.

 The mains lead has the

following specifications: 16/0.2mm - 3 core PVC covered - PVC
insulated wire to BS 6500.

IMPORTANT:

Mains lead wires:
Green and yellow – Earth
Blue – Neutral
Brown – Live

FOR THE MAINS PLUG USE A 3AMP FUSE. The
appliance is supplied with approximately 3 metres of wire and a
mains plug. A longer cable may be fitted as follows:
Resistor

(a)

Remove the socket and plug from the cable supplied.

(b)

Re-assemble on the longer cable ensuring both
socket and plug are wired correctly.

If a different mains plug is used from the one supplied with
appliance proceed as follows:

The wire which is coloured green and yellow must be
connected to the terminal in the plug which is marked by
the letter ‘E’ or by the earth symbol   or coloured green or
green and yellow. The wire which is coloured blue must be
connected to the terminal which is marked with the letter
N’ or coloured black. The wire which is coloured brown
must be connected to the terminal which is marked with
the letter ‘L’ or coloured red.

Summary of Contents for EBONY SUPER











Reviews: