background image

10.0 Care of the Boiler

17

© Baxi Heating UK Ltd 2011

10.5

In an Emergency

1. If a water or gas leak occurs or is suspected, the boiler
can be isolated at the inlet valves by turning their taps
through 90° (

1

/

4

turn) downwards

2. You can contact ‘

heateam

’ on telephone number 08448 711

545 or visit www.heateam.co.uk 

as soon as possible.

10.1

Cleaning the Outer case

The painted panels should be wiped with a damp cloth and
then dried completely. 

DO NOT USE ABRASIVE

CLEANING AGENTS.

10.2

Condensate drain 

The condensate drain, located at the bottom of the appliance,
must not be modified or blocked. Blockage will cause the
appliance to shut down. 

10.3

Protection & Precaution

1. The appliance incorporates frost protection for itself only,
fitted as standard.  In cold weather, if you are going away, turn
the appliance off at the time switch ONLY. Leave the mains
supply switched ON.

2. If a system frost thermostat has been fitted (your installer
will be able to advise you), then to operate correctly and
protect your system, the gas and electricity must be left on and
the appliance set in the central heating mode.

3. The boiler incorporates an integral pump protection feature
which continually monitors the time since the pump last
operated. To prevent seizure, the pump will operate for
approximately 1 minute if it has not run in the last 24 hours.

10.4

Fault Indication

1. If a fault occurs on the boiler an error code may be shown
on the facia display.

If you smell gas

Do not operate light switches
Do not operate any electrical equipment
Do not use a telephone in the hazardous area
Extinguish any naked flame and do not smoke
Open windows and doors in the hazardous area
Turn off the gas supply at the meter
Warn any other occupants and vacate the premises
Telephone the National Gas Emergency Service on:-
0800 111 999

Faulty boiler

If it is known or suspected that a fault exists 
on the boiler, it must not be used until the fault 
has been corrected by a competent person.

Warning !

Yellow Tap - Gas

Black Taps - Water

Summary of Contents for Duo-tec 2 Combi 40 GA





















Reviews: