Baxi 741 Installer'S Manual Download | Manualshive

Page: 11 / 34

background image

3.20

The appliance is fitted with an A.S.D (Atmosphere sensing device). If the

appliance closes down after a period of operation for no apparent reason, the consumer
should be informed to stop using the appliance until the installation and appliance have
been thoroughly checked. The A.S.D will shut the appliance down if an unacceptable
amount of harmful products of combustion accumulate. Under no circumstances should
the A.S.D be altered or bypassed in any way. Only a genuine manufacturers replacement
part should be fitted. The individual A.S.D components are not replaceable.

3.21

A fireguard complying with BS 8423 should be fitted for the protection of young

children, the elderly, or the infirm.

Page 11

INSTALLER GUIDE

Figure 5. Appliance dimensions.

«
...
9
10
11
12
13
...
»

Summary of Contents for 741



































Reviews:

No comments

Related manuals for 741

Brand: Restoration Hardware Pages: 4

MANDALAY Series

Brand: Warnock Hersey Pages: 38

VOYAGEUR GRAND INSERT GRAND-MBK-AU

Brand: Quadra-Fire Pages: 32

Brand: Pacific energy Pages: 24

Brand: Napoleon Pages: 112

American Comfort FP11

Brand: RedCore Pages: 6

Brand: Valor Pages: 46

Brand: Burn Tech Pages: 38

Brand: Bluegrass Living Pages: 8

Brand: IHP Pages: 8

Brand: Heat&Glo Pages: 82

Brand: Nibe Pages: 20

Brand: hergom Pages: 64

Brand: hergom Pages: 40

Brand: StyleWell Pages: 24

Brand: Blue Sky Outdoor Living Pages: 14

Brand: Portland Willamette Pages: 2

Direct Vent BLDV500

Brand: Monessen Hearth Pages: 1

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands