Baumuller b maXX 1000 Parameter Manual Download Page 136

Page: 136 / 210

Parameter description

Parameter manual

b maXX

1000

Document no. 5.07004.03

Baumüller Nürnberg GmbH

136

of 208

4.3

The wake up frequency must be higher than sleep frequency.

Figure 62:

Wake up/ sleep frequency

When output frequency

≤

sleep frequency

P1384

–

sleep

) and time > detection time

P1383

–

, it will go in sleep mode.

When min. output frequency

≤

PID frequency

≤

lower bound of frequency and sleep func-

tion is enabled (output frequency

≤

sleep frequency and time > detection time), frequency

will be 0 (in sleep mode). If sleep function is disabled, frequency command = lower bound
frequency.

When PID frequency < min. output frequency and sleep function is enabled (output fre-
quency sleep frequency and time > detection time), output frequency = 0 (in sleep mode).

If output frequency

≤

sleep frequency but time < detection time, frequency command =

lower frequency. If sleep function is disabled, output frequency =0.

P1384

This parameter sets the sleep frequency, for further information see

P1383

–

P1384

PID Stand-by Abschalt-Frequenz

0.00 to 600.00 Hz

PID sleep frequency

0.00

STOP

BM_u_SleepFrequency

100:1 Hz

Summary of Contents for b maXX 1000



















































































































































































































Search results

Summary of Contents for b maXX 1000

Reviews:

Related manuals for b maXX 1000

Brands by name

Popular brands

Baumuller b maXX 1000, Parameter Manual

Search results

Summary of Contents for b maXX 1000

Reviews:

Related manuals for b maXX 1000

Brands by name

Popular brands