background image

TP10449

PAGE 4

Model No..................................................... .......... 714 Friction
Minimum Sheet Size ............................. 3 x 5" (7.6 x 12.7 cm)
Maximum Sheet Size ........................ 14 x 20" (35.5 x 50.8 cm)
Minimum Size Fold ........................................ 2 1/4" (5.7 cm)
Maximum Paper Weight .................................... 65 lb. Cover
Stack Height ........................................................ 2" (5.1 cm)
Fold Roll Speed ......................... Infinitely variable between

0"/min. and 7200"/min.

(18,288 cm/min. or 182 m/min.)

Fold Plate Depth ............................ #1 Plate, 13.5" (34.3 cm)

#2 Plate, 13.5" (34.3 cm)

Fold Roll Width .......................................... 14 1/8" (35.8 cm)
Fold Roll Diameter ......................................... 1 1/2" (3.8 cm)
Overall Physical Dimensions ................. Height 26" (66 cm)

Length 34" (88 cm)

Width 23 1/2" (60 cm)

Operating Voltage ........................ DOM. 110 VAC/1PH/60Hz

EXP. 220 VAC/1PH/60Hz

Power Consumption (folder) ................................ 250 Watts
Power Consumption (pump) .............................. 1500 Watts
Amperage (pump) ...................................... DOM. 13.6 Amp

EXP. 6.8 Amp

NOTICE

Immediately upon unpacking, carefully inspect each of the above assemblies for shipping damage.  If any damage is

found, be sure to contact the delivery freight carrier to file a damage claim.  Save all packaging material for the claims
adjustor to inspect.

3.0 INSTALLATION

3.1 Unpacking & Inspection

The 714 Friction is packaged in one carton, crated  as

one package.  It is broken down into 10 major assemblies
for shipment.  These are:

A) Main Folder Assembly
B) Feed Table Assembly
C) Slitter Shaft Assembly
D) Stacker Wheel Assembly
E) Accessory Package
F) Fold Roll Guards (2)
G) Stacker Tray
H) Fold Pans (2)
I) Literature Package
J) 1/2 Pint Surewash

1.0 INTRODUCTION

Your new 714 Friction Feed Folder has been designed to give you many years of useful service provided it is

installed, maintained, and operated according to the instructions in this manual.

Your 714 Friction  is a unique and versatile paper folding machine, capable of folding paper measuring between 3 x 5

inches (7.6 x 12.7 cm) and 14 x 20 inches (35.5 x 50.8 cm).  The 714 Friction  will make six types of folds: single fold, letter
fold, fan fold, French fold, double-parallel fold and a double letter fold, with a few simple settings. (Note: The French fold
and double-letter fold requires either two passes or the use of a right-angle unit).

Your 714 Friction is built rigid enough to ensure years of trouble-free performance, and at the same time, is compact

enough to fit on any table or desk.  It is portable so it can be moved anywhere it is needed.

2.0 SPECIFICATIONS

Summary of Contents for 714













Reviews: