manualshive.com logo in svg

Baumer O200, Instruction Manual

Share
Download
Baumer O200 Instruction Manual Download Page 30

 

en_BA_O200_IO-Link_V1.docx 

30/34 

Baumer Electric AG 

15.08.2018/ 

 

Frauenfeld, Switzerland

 

5.2.2 

Single Point Mode: 2-Point Teach (Only O200.G, O200.R) 

Defines SP1 based on TP1 and TP2 for an optimized switching behaviour. 
 
O200.G: 
Teaches the position of the object and of the background. 
 
O200.R: 
Teaches the sensor hitting the reflector with and without an object in between 
 
Command sequence: 

- 

Place object at desired switching distance 

- 

Execute 

Teach SP1 TP1 

to teach TP1 

- 

Execute 

Teach SP2 TP2

 to teach TP2 

- 

Execute 

Teach Apply

 to store the setpoint 

 

 

Figure 26: 2-Point Teach, switching behavior 

O200.G: 

SP1 = (TP1 + TP2) / 2 

O200.R: 

SP1 = sqrt(TP1 * TP2) 

 

5.2.3 

Window Mode: Window Teach (Only O200.G)  

If the selected SSC is configured to Window mode (Section 4.3.2.1), following command sequence can be 
applied to teach-in SP1 and SP2: 
 
Command sequence: 

- 

Place object at desired switching distance 

- 

Execute 

Teach SP1

 to teach-in the distance related to SP1 

- 

Execute 

Teach SP2

 to teach-in the distance related to SP2 

- 

Execute 

Teach Apply

 to store the setpoint 

By executing 

Teach Cancel

 the teach-in procedure can be canceled at any state as long 

Teach Apply

 has not 

been used before. 
 

 

Figure 27: Window Teach, switching behavior

 

 
Which SP was teached at a higher distance does not have any influence on the switching behavior 
(SP1<SP2, SP1>SP2). 

Summary of Contents for O200



































Reviews:

No comments

Brands by name

Popular brands

Load more brands