background image

 

SAFETy AND ATTENTION INSTRUCTIONS

MB248EN - 11171699, 17A2, Baumer_HMG10-PROFINET_II_EN

 4/29

2.2 

Attention instructions for mounting and operation

 

)

Risk of destruction due to electrostatic charge  

Electronic parts contained in the encoder are sensitive to high voltages�

 

» Do not touch plug contacts or electronic components�

 

» Protect output terminals against external voltages�

 

» Do not exceed max� operating voltage�

 

)

Risk of destruction due to mechanical overload  

Rigid mounting may give rise to constraining forces�

 

» Never restrict the freedom of movement of the encoder� The installation instruc-

tions must be followed�

 

» It is essential that the specified clearances and/or angles are observed.

 

)

Risk of destruction due to mechanical shock  

Violent shocks, e� g� due to hammer impacts, can lead to the destruction of the 

sensing system�

 

» Never use force� Assembly is simple when correct procedure is followed�

 

» Use suitable puller for disassembly�

 

)

Risk of destruction due to contamination  

Dirt penetrating inside the encoder can cause short circuits and damage the optical 

sensing system�

 

» Absolute cleanliness must be maintained when carrying out any work on the open 

terminal box�

 

» When dismantling, never allow lubricants to penetrate the encoder�

 

)

Risk of destruction due to adhesive fluids  

Adhesive fluids can damage the optical sensing system and the bearings. Dismoun-

ting an encoder, secured to a shaft by adhesive may lead to the destruction of the 

unit�

 

» Do not use adhesive fluids for fixing.

Summary of Contents for HMG 10 PROFINET

































Reviews: