background image

My appliance isn’t working correctly 

 

IMPORTANT: If your appliance appears not to be 
operating correctly, then you should disconnect it 
from your mains supply and then contact the 
Customer Care Department on telephone number 
(0118) 933 6911. 
 
DO NOT ATTEMPT TO REPAIR THE APPLIANCE 
YOURSELF. 

 

 

Please note that if an engineer is asked to attend whilst the product is 
under guarantee and finds that the problem is not the result of an 
appliance fault, then you may be liable for the cost of the call out 
charge. 
 

The appliance must be accessible for the engineer to perform 
any necessary repair. If your appliance is installed in such a 
way that an engineer is concerned that damage will be caused 
to the appliance or your kitchen, then he will not complete a 
repair.  
 
This includes situations where appliances have been tiled in, 
sealed in with sealant, have wooden obstructions placed in 
front of the appliance, like plinths. Or any installation other 
than the one specified by Baumatic Ltd. has been completed. 

 
Please refer to the conditions of guarantee that appear on the 
warranty card that you receive with the appliance. 
 

IMPORTANT: Baumatic Ltd. operates a policy of continuous 
improvement and reserves the right to adjust and modify its 
products without prior notification. 

 

25

Summary of Contents for BHG640SS





























Reviews: