background image

8

5) GAS CONNECTION

The gas connection is located in the rear and on the

underside of the appliance 100 mm from the right

hand side.

A. 

The hotplate can be connected with rigid pipe as

specified in AS5601 table 3.1.

B. 

If installing with a hose assembly, install with a

hose assembly that complies with AS/ANZ 1869

(AGA Approved), 10mm ID, class B or D, no more

than 1.2m long and in accordance with AS5601.

Ensure that the hose does not contact the hot

surfaces of the hotplate, oven, dishwasher or any

other appliance that may be installed underneath or

next to the hotplate. The hose should not be

subjected to abrasion, kinking or permanent

deformation and should be able to be inspected

along its entire length with the cooktop in the

installed position.

Unions compatible with the hose fittings must be

used and all connections tested for gas leaks.

Natural Gas

Natural Gas installations require the connection of

a gas regulator at the appliance. 

Assemble the regulator (noting the gas flow

direction) and transition pieces (supplied with the

appliance), in accordance with figure 12.

The transition piece on the supply side of the

regulator must be provided by the installer.

Liquified Petroleum Gas

In a LPG installation the gas regulation is made at

the gas cylinder and regulation at the appliance is

not required. To connect supply to the appliance

use transition pieces as shown in figure 12. These

pieces  are  supplied  with  the  appliance  on

purchase.

WARNING:

THE BURNER FLAME MUST BE ADJUSTED BY

THE INSTALLER.

FAULTY  INSTALLATION  WILL  NOT  BE

COVERED UNDER WARRANTY.

THE  APPLIANCE  IS  FACTORY  SET  FOR

NATURAL GAS. THE TEST POINT PRESSURE

SHOULD BE ADJUSTED TO 1.00kPa WITH THE

WOK BURNER OPERATING AT MAXIMUM.

INSTALLATION

FIG. 11

FIG. 12

IMPORTANT: 

a  perfect  installation,  adjustment  or

transformation of the cook top to use other

gases requires a QUALIFIED INSTALLER: a

failure  to  follow  this  rule  will  void  the

warranty.

Summary of Contents for BGH60

















Reviews: