background image

o

 

Great care should be taken whilst using this appliance and when 
following the cleaning procedure.

 

 

o

 

You should not use a steam jet or any other high pressure 
cleaning equipment to clean the appliance.

 

 
Installation 

 
This appliance must be correctly installed by a 
CORGI registered installer, strictly in accordance 
with the manufacturer’s instructions and the 
relevant British Standards. Please see the specific 
section of this booklet that refers to installation. 
 

o

 

Baumatic Ltd. declines any responsibility for injury or 
damage, to person or property, as a result of improper 
use or installation of this appliance.
 

 

o

 

If the appliance is being used in a Leisure Accommodation 
Vehicle, the requirements of N 721 MUST be followed.
 

 

o

 

Baumatic Ltd. DO NOT recommend that this appliance is 
installed on any type of marine vessel. 

 
Declaration of conformity 
 
This appliance complies with the following European Directives: 

 
-73/23/EEC dated 19/02/1973 Low Voltage Directive. 
-89/336/EEC dated 03/05/1989 EMC Directive inclusive of 
Amending Directive 92/31/EEC. 
-93/68/EEC dated 22/07/1993 CE Marking Directive. 
-89/109/EEC dated 25/01/1992 Materials that can touch food. 
-90/396/EEC Gas Products. 
-EN60335-1, EN60335-2, EN301-1 Safety Standards. 
 

The manufacturer declares that the hob is built using certified 
materials and requires the appliance to be installed in accordance with 
the standards currently in force. This appliance must be used by a 
trained person for domestic purposes only. 
 
 
 
 
 
 
 
 
 

 

7

Summary of Contents for B17.5SS





























Reviews: