manualshive.com logo in svg

Baumalight TRL620Y, Operator'S Manual

Share
Download
Baumalight TRL620Y Operator'S Manual Download Page 37

5.6 Every 250 Hours

Change Engine Oil And Filter

Skidsteer must be parked on a level surface, park 

brake engaged, lift arms fully lowered, engine 

stopped and key removed. 

Remove oil plug (A), drain engine oil and replace 

filter (B) every 250 hours. Install plug (A), new filter 

(B) and proper quantity of engine oil.

A

B

The  OEM  engine  manufacturer  specifies  the  oil 

be  API service categories CD, CF, CF-4, CI-4 or 

higher. Change the type of engine oil according to 

the ambient temperature.

32° F

0° C

50° F

10° C

68° F

20° C

86° F

30° C

104° F

40° C

-22° F

-30° C

-4° F

-20° C

14° F

-10° C

SAE 

10W-30

SAE 

5W-30

SAE 

15W-40

SAE 30

SAE 20

Refer to the OEM engine manual for detailed oil 

information and recommendations. 

Check Air Intake Hoses

Check air intake hoses for wear and damage.  

Tighten clamp if loose. Replace worn, damaged or 

leaking parts.

Check Engine Fan Belt

Skidsteer must be parked on a level surface, park 

brake engaged, lift arms fully lowered, engine 

stopped and key removed. Check belt for wear 

and damage. See engine operators manual. 

33

Summary of Contents for TRL620Y

















































Reviews:

No comments

Brands by name

Popular brands

Load more brands