background image

16

Care and maintenance

Clean the hob after each use in order to avoid damaging 
the surface and to prevent the formation of baked-on 
deposits which are difficult to remove. Before cleaning, 
make sure the cooking zones are switched off and that the 
residual heat indicator (“H”) is not displayed.

Never clean the hob with a steam cleaner! 

Periodically check for dust under the 
appliance, near the cooling air inlet or the 
outlet openings. This could hinder the 
ventilation and cooling of the electronic 
module and decrease the effectiveness of the 
hob.

To clean the hob, proceed as follows:

1.

use a soft clean cloth, absorbent kitchen wipes or a 
proprietary cleaner for glass ceramic hobs. Do not use 
abrasive sponges and/or metal scouring pads.

2.

Food spills should be cleaned off before they bake 
onto the glass ceramic surface. Sugar and foods with a 
high sugar content damage the glass ceramic surface 
and must be immediately removed using a scraper for 
glass. Caution! Glass scrapers have a very sharp blade 
and must be handled with care.

3.

Remove any stubborn food residues with a scraper or 
proprietary detergents.

4.

Salt, sugar and sand can scratch the glass ceramic hob: 
clean up any such spills on the hob immediately.

Troubleshooting Guide

Before contacting After-sales Service:

read and follow the instructions given in the section 
“Operating instructions”.

Connect the hob to the electricity supply and check that 
the supply has not been shut off.

Clean the hob and dry it thoroughly.

If, when the hob is switched on, alphanumeric codes 
appear on the display, consult the following table for 
instructions.

Important!

 If you are unable to turn the glass-ceramic hob off after using it, disconnect it immediately from the 

power supply.

After-sales Service

Before contacting After-sales Service:

Try to solve the problem (see “Troubleshooting 
Guide”).

Switch the appliance off, wait 30 seconds then switch it 
on again. to see if the fault persists.

If after the above checks the fault persists, contact the 
nearest After-sales Service.

Always provide:

a brief description of the fault;

the exact type and model;

the service number (number after the word Service on 
the rating plate) is located on the underside of the 
cooktop or on the warranty booklet;

your complete address and phone number.

If any repairs are required, please contact an authorized 
After-sales Service as indicated in the warranty.

MAINTENANCE

ERROR CODE

DESCRIPTION

POSSIBLE CAUSES

REMEDY

The hob switches off 

and after 30 seconds 

emits an acoustic signal 

every 4 seconds 

Continuous pressure on 

control panel area

Water or utensils on control panel

Clean the control panel

C81, C82

The control panel switches off 

because of excessively high 

temperatures

The internal temperature of 

electronic parts is too high

Wait for the hob to cool down 

before using it again

F42 or F43

The connection voltage is 

wrong

The sensor detects a discrepancy 

between the appliance voltage and 

that of the mains supply

Disconnect the hob from the 

mains and check the electrical 

connection

F12, F21, F25, F36, 
F37, F40, F47, F56, 

F58, F60

Call the After-Sales Service and specify the error code

41902022GB.fm  Page 16  Monday, June 23, 2008  12:39 PM

Summary of Contents for ETI 6646











Reviews: