Bauer S655 Original Operating Manual Download

Page: 19 / 35

Operating Manual for

BAUER Plug & Play Separator System

INITIAL STARTUP

NOTE

Before starting up the system, please read the operating manual of the sepa-
rator, eccentric screw pump and control (see attachment)

NOTE

The reaction time before each setting change takes several minutes, meaning
that the effect of any change can only be determined after this time.

For this reason, always allow enough time after making a change and only make
changes in small steps!

NOTE

Before the initial startup and after prolonged downtime, the separator should
be flooded before switching it on by starting the pump briefly in order to pre-
vent possible damage from dry running.

NOTE

In order to achieve good separating results, it is necessary to mix the
pumped medium well before separating.

Motor circuit breakers:

All motor protection switches (

5F1, 5F2, 5F3, 6F1, 6F2, 7F1

) check on the proper nominal current of the

respective electric motors or set and then activate

Figure 7 motor ciurcuit breakers

2F1

7F1

6F2

6F1

5F3

5F2

5F1

Summary of Contents for S655




































Search results

Summary of Contents for S655

Reviews:

Related manuals for S655

Brands by name

Popular brands

Bauer S655, Original Operating Manual

Search results

Summary of Contents for S655

Reviews:

Related manuals for S655

Brands by name

Popular brands