manualshive.com logo in svg

Bauer Magnum SM 1000, Operating Manual, Page: 2 / 30

Share
Download
Bauer Magnum SM 1000 Operating Manual Download Page 2

II

Operating manual for 

BAUER gear pump

INTRODUCTION

Thank you very much for purchasing a BAUER gear pump!

We are pleased to offer you a  

BAUER gear pump 

featuring state-of-art technology and top quality.  This

manual describes how to operate and maintain the 

BAUER gear pump

. For reasons of clearness and due to

the many possibilities this manual does not contain everything down into detail.  In particular,   it cannot possibly
take into consideration every conceivable aspect of operation and maintenance.
If you need further information or if you should be faced with any particular problems for which this manual does
not offer sufficient details please feel free to contact 

BAUER company 

at Kowaldstraße 2, A-8570 Voitsberg for

the information you need.
Please note that the content of this operating manual neither constitutes part of nor does it alter any previous or
existing agreement, promise or legal relationship. Any commitment on the part of 

BAUER

 is a result only of the

individual purchase contract that also contains the complete and only valid warranty arrangement. Said
contractual terms of warranty are neither extended nor limited by the content of the present operating manual.
All information contained in the present manual is based on the latest product details available at the time of
printing.

BAUER 

reserves the right to change without prior notice, without assuming any liability!

BAUER gear pumps

 are designed for safe and reliable operation provided they are operated in compliance with

the present instruction manual.  In spite of the simplicity of the pump we therefore request that you read this
manual carefully before putting your 

BAUER gear pump 

into operation! All instructions given for handling,

operating and servicing the pump must be strictly observed.  Provided these instructions are followed the pump
will operate trouble-free to your full satisfaction for many years!
Non-observance of our instructions may result in injury or equipment damage!

Please make this manual available to your operating personnel.  You are kindly requested to state the pump type
and serial number of the gear pump in all inquiries, correspondence, warranty problems or parts orders.  These
details are specified on the nameplate.

We hope you will enjoy working with your BAUER gear pump!

This operating manual should be considered an integral part of the gear pump. Suppliers of new and used
pumps are advised to put down in writing that this manual was handed over together with the pump.

Summary of Contents for Magnum SM 1000































Reviews:

No comments