Baudouin 12M26 Series Operation And Maintenance Manual Download Page 25

Page: 25 / 83

O&M Manual for PowerKit M26 Series Diesel Engine

2.6 Fuel System

2.6.1 Fuel circuit diagrams of 6M26

The fuel pump draws the fuel from the genset fuel tank through pre-filter/water-separator and

through full flow filter to the injection pump.

Injection pump delivers fuel under high pressure to the injectors.

Excess fuel not injected is returned to the fuel tank.

Injector holder leakages return to fuel tank.

Engine is equipped with high pressure pipe leakage detector, overflow is return to tank.



Overall Layout of Fuel System

Figure2.6.1-Overall Layout of Fuel System

1-Tank with Pre-filter

2-Pre-fuel Filter

3-Solenoid Valve

4-Main Fuel Filter

5-Injection Pump

6-Low Pressure Circuit

7-High Pressure Circuit

8-Injector

9-Fuel Return Pipe

Summary of Contents for 12M26 Series




















































































Search results

Summary of Contents for 12M26 Series

Reviews:

Related manuals for 12M26 Series

Brands by name

Popular brands

Baudouin 12M26 Series, Operation And Maintenance Manual

Search results

Summary of Contents for 12M26 Series

Reviews:

Related manuals for 12M26 Series

Brands by name

Popular brands