Baudcom BD-ONT-212GW-AC5 User Manual Download Page 68

Page: 68 / 78

2LAN+1POTS+WiFi Dual Mode HGU USER MANUAL

Website : www.baudcom.com.cn Tel: +86 21 37709251 Email:

[email protected]

Page 64

Figure 4-15: Add a WAN connection for IPTV service

Add a route mode WAN connection for VOIP service. Choose IPv4 and static; fill up the IP

address, mask, gateway, DNS etc. Enable VLAN, VLAN ID is 3000. Service mode is VOIP.

Figure 4-16: Add a WAN connection for VOIP service

Configure VOIP general parameters

Choose “Application > VOIP > VOIP Configuration” in navigation menu. Configure VOIP

general parameters as the following shows.



“Region” contains many countries or regions. Different regions have their own dial tone

and ringing tone, etc.



“Proxy server” and “Registering server” both are 192.168.3.19, port is 5060;



Fill up phone number, username and password of each line.



Choose packing time, default is 20ms.

Summary of Contents for BD-ONT-212GW-AC5















































































Search results

Summary of Contents for BD-ONT-212GW-AC5

Reviews:

Related manuals for BD-ONT-212GW-AC5

Brands by name

Popular brands

Baudcom BD-ONT-212GW-AC5, User Manual

Search results

Summary of Contents for BD-ONT-212GW-AC5

Reviews:

Related manuals for BD-ONT-212GW-AC5

Brands by name

Popular brands