background image

9

BATTERY REPLACEMENT

1.  Remove the (4) corner screws attaching the flow meter electronics and 

Bluetooth module to the meter and lift away from the meter.

2.  Remove the 

AAA

 batteries from the display and then the 

CR2477

 3V lithium 

cell battery from the Bluetooth module. 

3.  Check the battery terminals and remove any corrosion.
4.  Install the new batteries, preferably starting with the 

AAA

 cell battery. For the 

AAA

 batteries, make sure the positive posts are positioned correctly. When 

the batteries are installed correctly, the flow meter powers on automatically 

and the display will show information.

5.  Install the 

CR2477

 battery with the positive side up. 

6.  Make sure the seal is fully seated before placing the flow meter electronics 

back on the turbine. Make sure wires aren't obstructing the seal. Tighten the 

(4) screws previously removed.

7.  Do not clean exterior of flow meter assembly with Isopropyl Alcohol, use a 

damp cloth as needed.

NOTE: It is recommended to replace the batteries every year.  

WARRANTY

This product is warranted against defects in workmanship and materials 

for a period of one year from date of shipment.

Summary of Contents for Direct Fill Link+

















Reviews: