1. Introduction
The Vector Fly System contains a wide range of insect light
traps that are designed to meet the needs of various fly-
ing insect infestations and locations. Each light trap in the
system utilizes ultraviolet light to lure the insect to the trap
where it becomes trapped onto a glue surface. There are no
exploding insect parts, no popping or sizzling – the insects
are trapped fully intact. Because insects are captured fully
intact, Vector insect light traps may be used for monitoring
insect populations and can be placed in food handling areas.
2. Product Description
The Vector Plasma is the latest advancement in insect light
trap design and engineering. It utilizes two flat 36 watt
bulbs, positioned to maximize fly attraction and capture on
the Vector Universal Glueboard. With its slim design, light-
weight aluminum construction, electronic ballast and ease
of glueboard and bulb change-out, the Vector Plasma will
provide years of reliable service with minimal maintenance.
It is ideal for use in restaurants, bars, commercial kitchens,
food prep areas, grocery stores, bakeries, warehouse stor-
age areas, hospitals and schools.
3. Safety Instructions
CAUTION:
This product is intended for commercial in-
door use only. The device is not constructed for use out-
doors or in wet locations, and therefore, it is not suitable
for use in barns, stables or similar locations. To avoid
risk of fire or electrical shock, do not use where it may
be exposed to water or direct sunlight, including roofed
or open porches.
WARNING:
Shock hazard. Do not open. There are
no user serviceable parts inside. The user may replace
glueboards and bulbs. Qualified service personnel must
perform all other repairs and maintenance. Store the unit
indoors when not in use – out of reach of children. The
product is not intended for use by young children or infirm
persons. Young people should be supervised to ensure
they do not play with the product. To maximize safety,
disconnect the unit from the power supply when not in
use, when changing bulbs, cleaning, etc. Do not abuse
the cord, carry the product by the cord or unplug the unit
from the electrical outlet by pulling on the cord. Keep cord
away from heat, oil and sharp edges. Do not use the product
if the cord is damaged. To provide continuous protection
against the risk of electrical shock, connect the plug only to
a grounded outlet. Do not insert foreign objects into the unit.
The unit must not be installed where dangerous concentra-
tions of flammable or explosive substances are likely to occur
in the air. Do not use the unit near concentrated oxygen or
store the glueboards near concentrated oxygen.
4. Grounding Instructions
The Vector Plasma is equipped with an appropriate 3-con-
ductor cord and 3-prong grounding plug to fit grounding type
electrical outlets. To reduce the risk of an electric shock, the
plug must be plugged into an appropriate electrical outlet that
is properly installed and grounded. Consult a suitable quali-
fied person if the grounding instructions are not completely
understood, or if in doubt as to whether proper grounding
exists. Extension cords are not to be used with this unit.
5. Unpacking
Each Vector product is carefully packed before leaving the
factory to ensure it reaches you in perfect working order. Re-
move all packaging from the product before installation.
6. Guidelines for Placement
Proper placement is key to achieving maximum efficiency with
the Vector Fly System. Below are general guidelines.
• Install the Vector Plasma where insect contact is most probable.
• Locate the Vector close to an opening, but avoid placement
where outside light may interfere with insect attraction. Do
not install the unit directly next to competing light sources.
• Place the Vector so that the light from it is not visible from
the outside of the building.
• Mount the Vector 4 to 6 feet off the floor whenever possible.
• Always keep in mind that the Vector will be most effective
when placed where flies congregate. For example:
o Near food prep areas where food is readily available (avoid
installing directly over food prep surfaces)
o Near passages from food prep areas to public areas
o Around indoor trash collection areas
o Identify natural wind and air currents to ensure flies can
reach the Vector
7. Placement Options
The Vector Plasma can be mounted in a number of positions
(see diagrams below). Decide on an appropriate mounting
option suitable for your location.
