BASEWEST TS-420 Operating & Maintenance Manual Download Page 10 | Manualshive

Page: 10 / 10

BASEWEST TS-420 Operating & Maintenance Manual Download Page 10

BASEWEST

Operating & Maintenance Manual

Model TS-420 Test Set

Page 10 of 10

25-60-41

24 Jan 2002

•

Do not apply external electrical inputs, except AC charger

•

Keep instrument away from all fluids

•

Protect from extreme temperatures, weather/rain, extended UV radiation

7.2 The device is designed for handheld use in a shop and field environment but is not

designed to withstand a drop to the ground or to survive excessive compression loads.

7.3 The device is splash resistant, but not waterproof; do not allow the device to sit in standing

fluids or subject to rain. Excessive exposure to UV can affect the LCD meter.

7.4 Surface cleaning only with a slightly damped cloth (water or alcohol) is recommended. DO

NOT use other solvents or cleaners.

8.0 Calibration and Repair

The TS-420 test sets should be calibrated in accordance with the user's quality assurance
requirements. A separate calibration manual is provided; contact BaseWest for
distribution. Unauthorized field repairs are not recommended, and may void warranty. It
is recommended that the devices be returned to BaseWest for repair or servicing.

«
...
8
9
10

Summary of Contents for TS-420











Reviews:

No comments