background image

BARTINGTON INSTRUMENTS

 

Page 4 of 16

1. Legal notices

1.1. Copyright

The copyright of this document is the property of Bartington Instruments Ltd.

1.2. Trademarks

Bartington® is a trademark of Bartington Instruments Ltd in Australia, Canada, China, the 
European Community, India, Japan, the countries of the Madrid Agreement & Protocol™, Norway 
and the United States of America.

1.3. Warranty and Terms & Conditions

This document should be read in conjunction with the Terms & Conditions for the Supply of 
Goods and Services, which also describe the terms of warranty. They are available at 

www.

bartington.com/terms-and-conditions.html

.

Bartington Instruments reserves the right to change any part of the design of these products 
without prior notice.

2. How to use this manual

This document describes the installation, operation and maintenance of the Mag585 and Mag592 
Magnetic Field Sensors.

Take the time to get well acquainted with your purchase by reading this manual. Knowing and 
understanding your sensor will ensure you experience the most reliable operation.

When service or maintenance is required, contact the Bartington Instruments service team.

Technical specifications for these products can be found in the appropriate product brochures on 
the product pages of the Bartington Instruments website:

www.bartington.com/mag585-low-radiation-three-axis-magnetic-field-sensor.html

www.bartington.com/mag592-low-radiation-single-axis-magnetic-field-sensor.html

2.1. Symbols glossary

The following symbols used within this manual call your attention to specific types of 
information:

Summary of Contents for Mag585

















Reviews: