background image

 

2

Safety Instructions  

 

 
1. Please read these instructions and keep them for reference. 
 
 
2. Please follow all instructions described here. 
 
 
3. Do not use this apparatus near water. 
 
 
4. Clean only with a dry cloth. 
 
 
5. Do not block any ventilation openings. 
 
 
6. Do not operate near any heat sources such as radiators or heat registers. 
 
 
7. Protect the power cord from being walked on or pinched, particularly at the plugs and at the 
point where they exit from the apparatus. 
 
 
8. Only use attachments/accessories specified by the manufacturer. 
 
 
9. Unplug this apparatus during lightning storms or when unused for long periods of time.  
 
 
10. Refer all servicing to qualified service personnel.  Servicing is required when the apparatus 
has been damaged in any way.  For example, if the power supply cord or plug is damaged, liquid 
has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to 
rain or moisture, does not operate normally, or has been dropped. 
 
 
11. CAUTION: To disconnect the unit completely from the MAINS, unplug the unit. 
Turning the power switch off does not disconnect the unit completely from the MAINS. 
 

 

 

 

Summary of Contents for Sugarland


















Reviews: