Installation Instruction
Xbeam LTE EX Antenna
BARTEC
TECHNOR AS
Vestre Svanholmen 24
4313 SANDNES
NORWAY
Tel.: +47 51 844100
Fax: +47 51 844101
[email protected]
www.bartec-technor.no
Reservation
Technical data subject to change without notice. Changes, errors and
misprints may not be used as a basis for any claim for damages.
EN 4/4
24
05
2-
5
v1
In
st
al
la
tio
n
In
st
ru
ct
io
ns
X
b
ea
m
L
T
E
E
X
Commissioning
Before commissioning, check that:
The product has been installed in compli-
ance with the manufacturer instructions.
The product is not damaged.
The device functions perfectly.
Perform an ‘Initial Inspection’ according to
EN IEC 60079-14.
Operation
Death or serious injury through improper
use.
The
Xbeam LTE EX
may be operated only
within the technical limits that apply to it (see
page 1).
The
Xbeam LTE EX
Antenna is a sealed
device with a flying lead Coax Cable. It is
not possible to take the antenna apart. If the
antenna for some reason breaks, it must be
replaced with a new antenna.
Due to potential electrostatic charging haz-
ard of the black polycarbonate housing of
the antenna, cleaning must only be done
with a clean, wet cloth.
Maintenance and Fault Clearance
Risk of injury due to incorrect proceedings.
The national valid regulatory for mainte-
nance, inspection, and repair is applicable
for electrical equipment for the use in haz-
ardous areas.
Damaged Ex components must be directly
replaced by genuine BARTEC parts.
Maintenance cycles
The
Xbeam LTE EX
Antenna does not require
any specific maintenance at regularly scheduled
intervals. One must make sure that the antenna
is kept free of dust.
In case of malfunction, it must be replaced with
a new antenna.
Inspection of the
Xbeam LTE EX
Antenna is lim-
ited to ensuring that encapsulation, seals and
mounting are tight and secure. There are no
moving parts or adjustments possible, nor can
the housing be opened.
Any attempts made to open the housing, may
void the warranty.
Inspection
Follow the national law and regulatory for in-
spection of explosion proof equipment. This
should be done by skilled and qualified person-
nel only.
Replacing the
Xbeam LTE EX
•
In case of a fatal error of a
Xbeam LTE EX
,
the antenna must be replaced by a new
unit. Repair or maintenance are not al-
lowed by unauthorized personnel.
Troubleshooting
•
Troubleshooting involves checking the
functionality of the antenna. If you require
assistance, contact your distributor.
Specific conditions
The
Xbeam LTE EX
Antenna shall be marked
with the following warning text:
‘POTENTIAL ELECTROSTATIC CHARGING
HAZARD - SEE INSTRUCTIONS’
The use of the device in case of excessive de-
posits of dusts superior of 50mm
according to EN / IEC 60079-31 is not allowed.
Disposal
The sensor contains metal, electronic compo-
nents and plastic parts. Therefore, the statutory
requirements for disposing of electronic scrap
(WEEE) must be observed (e.g. disposal by an
approved disposal company). The sensor is also
marked with the wheeled bin symbol for WEEE:
Service Addresses
BARTEC TECHNOR AS
Vestre Svanholmen 24, N 4313 Sandnes
Norway
BARTEC Explosion Proof Appliances
(Shanghai) Co., Ltd.
New Building 7, No. 188 Xinjun Ring Road
Caohejing Pujiang Hi-tech Park
CN 201114 Shanghai
China
BARTEC GmbH
Max-Eyth-Str. 16, D 97980 Bad Mergentheim
Germany
BARTEC Middle East FZE
RA-08, HB-01, Jebel Ali Free Zone, Dubai
United Arab Emirates
BARTEC NEDERLAND B.V.
Boelewerf 25, NL 2987 VD Ridderkerk
Netherlands
BARTEC Pte. Ltd.
63 Hillview Avenue, #07-20/23 Lam Soon Build-
ing, SG 669569 Singapore
Singapore
BARTEC US Corp.
650 Century Plaza Drive, Suite D120
Houston, TX 77073
USA
BARTEC Varnost d.o.o.
Cesta 9. Avgusta 59, SI 1410 Zagorje ob Savi
Slovenia
