manualshive.com logo in svg

Baroness LM2700, Service Manual

Share
Download
Baroness LM2700 Service Manual Download Page 224

Install the tie rod. (See "Installation of Tie
Rod" (Page 7-30) .)
Install the steering cylinder. (See
"Installation of Steering Cylinder" (Page
5-82) .)
Install the rear wheel. (See "Installation of
Rear Wheel" (Page 7-19) .)

Removal of Tie Rod

Important

Take note of the direction of the tie rod when
removing it.

Remove the cotter pin, and then remove
the slotted nut.

1

2

g39lnk-001

Removal of the Tie Rod_001

1

Cotter pin

2

Slotted nut

Tap the joint part of the tie rod end with a
plastic hammer to remove the tie rod.

3

1

2

g39lnk-003

Removal of Tie Rod_002

4.

5.

6.

1.

2.

1

Tie rod end installation part

2

Plastic hammer

3

Tie  rod

Installation of Tie Rod

Caution

See "Tightening torques" (Page 3-5) .
Note that the Baroness product warranty may
not apply to defects caused by incorrect or
overtorque tightening etc.

Important

Check the orientation in order to install the tie
rod in the correct orientation.

For installation, reverse the removing
procedure.

Steering

Removal of Steering

Remove the rubber cap, and then remove
nut and spring washer.
Pull up the steering upwards to remove it.

1

2

3

4

4azbue-002

Removal of Steering_001

1

Rubber cap

2

Nut

3

Spring washer

4

Steering wheel

1.

2.

LM2700

Main body

Page 7-30

Removal and installation of each section

Summary of Contents for LM2700






































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands