background image

24

BARMESA PUMPS

FACTORY WARRANTY

Barmesa Pumps warrants that products of our manufacture will be free of defects in material and 
workmanship under normal use and service for 18 months from date of manufacture or 12 months 
from installation date whichever occurs first. This warranty gives you specific legal rights, which vary 
from state to state.

This warranty is a limited warranty, and no warranty related claims of any nature whatsoever shall be 
made against Barmesa Pumps, until the ultimate consumer or his/her successor notifies us in writing 
of the defect and delivers the product and/or defective part(s) freight prepaid to our factory or 
nearest authorized service station as instructed by Barmesa Pumps. THERE SHALL BE NO FURTHER 
LIABILITY, WHETHER BASED ON WARRANTY, NEGLIGENCE OR OTHERWISE. PRODUCT SHALL BE 
EITHER REPLACED OR REPAIRED AT THE ELECTION OF BARMESA PUMPS. Guarantees relating to 
performance  specifications  provided  in  addition  to  the  foregoing  material  and  workmanship 
warranties on a product manufactured by Barmesa Pumps, if any, are subject to possible factory 
testing. Any additional guarantees, in the nature of certified performance specifications or time 
frame must be in writing and such writing must be signed by our authorized factory manager at time 
of order placement and/or at time of quotation. Due to inaccuracies in field testing and should a 
conflict arises between the results of field testing conducted by or for the user, Barmesa Pumps 
reserves the right to have the product returned to our factory for additional testing.

This warranty shall not apply when damage is caused by (1) improper installation, (2) improper 
voltage, (3) lightning, (4) excessive sand or other abrasive material, (5) corrosion build-up due to 
excessive  chemical  content  or  (6)  uncontrollable  acts  of  god.  Any  modification  of  the  original 
equipment will also void the warranty. We will not be responsible for loss, damage or labor cost due 
to interruption of service caused by defective pumps, parts or systems. Barmesa Pumps will not 
accept charges incurred by others without our prior written approval.

This warranty is void if our inspection reveals the product was used in a manner inconsistent with 
normal industry practice and/or our specific recommendations. The purchaser is responsible for 
communication  of  all  necessary  information  regarding  the  application  and  use  of  the  product. 
UNDER  NO  CIRCUMSTANCES  WILL  WE  BE  RESPONSIBLE  FOR  ANY  OTHER  DIRECT  OR 
CONSEQUENTIAL  DAMAGES,  INCLUDING  BUT  NOT  LIMITED  TO  TRAVEL  EXPENSES, 
CONTRACTOR  FEES,  UNAUTHORIZED  REPAIR  SHOP  EXPENSES,  LOST  PROFITS,  LOST  INCOME, 
LABOR CHARGES, DELAYS IN PRODUCTION, IDLE PRODUCTION, WHICH DAMAGES ARE CAUSED 
BY  ANY  DEFECTS  IN  MATERIAL  AND/OR  WORKMANSHIP  AND/OR  DAMAGE  OR  DELAYS  IN 
SHIPMENT. THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER EXPRESS OR IMPLIED WARRANTY. 
No rights extended under this warranty shall be assigned to any other person, whether by operation 
of law or otherwise, without our prior written approval.

IMPORTANT!

If you have a claim under the provision of the warranty, contact Barmesa Pumps or your

authorized Barmesa Pumps Distributor:

[email protected]

www.barmesapumps.com

barmesa.com

Summary of Contents for 2-125 HP @ 1750 y 3500 RPM


























Reviews: