manualshive.com logo in svg

BARIX Annuncicom IC, User Manual

Share
Download
BARIX Annuncicom IC User Manual Download Page 9

 

 

Annuncicom IC User Manual Version 01.20 

  

Page 

8 

7.3

 

Audio settings 

 
These settings adjust the audio input and output.  

 

 

Input source

 

Choose the desired input source. 
On Detect Source the device chooses the input with  
higher audio level during start up. 

Microphone gain

 

Choose the desired gain (

"21" - "43.5" dB) for the 

microphone. 

A/D amplifier gain

 

Choose the desired gain (

"-3" - "19.5" dB) for the A/D 

amplifier. 

Loop Input to Output

 

Choose 

"Yes" to hear the attached input on the local Line 

Out (For testing only, feedback may occure when using a 
speaker). 

Encoding

 

Choose between six different MP3 encodings (from 
"MPEG1 / 48 kHz" down to "MPEG2 / 16 kHz"), four 
different G.711 encodings (aLaw/uLaw, 8 or 24 kHz) and 
two 16bit PCM encodings (8 or 24 kHz). The network 
bandwidth used by G.711 at 8 kHz is 64kBit/sec and  
192kBit/sec at 24 kHz sampling frequency. PCM uses 16 bit 
and therefore needs the double bandwidth (128kBit/sec @ 
8 kHz and 348kBit/sec @ 24 kHz). For MP3 bandwidth 
usage see the next parameter. 
ATTENTION: Make sure to set all devices with the same 
encoding setting when choosing G.711 or PCM. 

Encoding Quality

 

Choose between 

"0 lowest" and "7 highest" in steps of 1. 

The Encoder Quality table below shows the average bit 
rate in kbit/s for the quality settings and sampling 
frequencies in kHz. 

Qual. 0 1 2 3 4

5

 

6

 

7

 

44.1 

65 68 73 80 90 105

 

125

 

140

 

22.05

35 38 40 45 50 60

 

75

 

90

 

 

Volume

 

Choose between 

"0%" and "100%" in 5% steps. 

Bass

 

Choose between 

"-10" and "10". 

Treble

 

Choose between 

"-10" and "10". 

Loudness Level

 

Choose between 

"0" and "20". 

Loudness

 

Choose between 

"0" and "20" and switch the Loudness 

"On" or "Off". 

MP3 Frame CRC

 

If set to 

"enable", the encoder will include the CRC-16 to 

each MP3 frame. 

MP3 Bitreservoir Mode

 

The Bitreservoir is used to compensate the differences 
between the predefined frame sizes. If set to 

"used", the 

encoder will use the bitreservoir. 

MP3 Copyright Protection

 

"Enable" or "disable" the copyright protection bit in the 
MP3 bitstream. 

MP3 Stream Type

 

Select between a 

"copy" or an "original" bitstream in order 

to set the appropriate bit in the MP3 bitstream. 

MP3 Emphasis

 

Select emphasis 

"none", "50/15 us" or "CCITT J.17". 

 

 
 
 
 
 

Summary of Contents for Annuncicom IC































Reviews:

No comments

Brands by name

Popular brands

Load more brands