manualshive.com logo in svg

Barco UDX, Installation Manual

Share
Download
Barco UDX Installation Manual Download Page 87

87

Purpose of the laser range finder & camera kit

Barco provides a kit with a laser range finder and USB camera to help measure the distance from the front of
the projector to the projected surface. And this by the simple press of a button.

This kit is specifically made for the UDX and thus cannot be used for other equipment.

How to use the laser range finder

Place the projector with laser range finder and point it towards the desired projected surface.

Press the push button to activate the laser and read the distance from the display. The laser will be active for
30 seconds.

In order to switch the unit of measurement, press the push button for 3 seconds. You can choose between
meters and feet.

WARNING:

Laser Radiation

—

Do not stare into laser ranging beam, Class 2 IEC EN 60825-1:2014

R5906113 /08

UDX

Laser range finder &
camera kit

8

Summary of Contents for UDX























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands