Barco SIM 7C R9011206 Service Manual Download Page 33 | Manualshive

Page: 33 / 44

background image

6. Optical parts and servicing procedures

Image 6-12
Lamp inserting:

fi

rmly push the bottom side

fi

rst

5. Then

fi

rmly push the top side of the lamp, while pushing the lamp locking handle down

Image 6-13
Lamp inserting:

fi

rmly push the top side...

Image 6-14
Lamp inserting: ... while pushing down the lamp locking handle

6.1.6

Installing the lamp door

Necessary tools

Torx screwdriver T10

How to install the lamp door?

1. Put the lamp door in the right position

Tip:

The two positioning points must coincide with the two positioning holes

Image 6-15
Lamp door: positioning points & holes

Image 6-16
Lamp door: positioning holes

2. Tighten the three screws

R59770119 SIM 7C 28/05/2008

29

«
...
31
32
33
34
35
...
»

Summary of Contents for SIM 7C R9011206













































Reviews:

No comments

Related manuals for SIM 7C R9011206

Brand: JBL Pages: 43

Brand: Barco Pages: 78

Brand: Barco Pages: 2

Brand: Barco Pages: 143

Brand: Barco Pages: 2

Brand: Barco Pages: 2

Brand: Barco Pages: 48

Brand: Barco Pages: 2

Brand: Barco Pages: 8

Brand: Barco Pages: 66

BarcoReality SIM6 Ultra R9040150

Brand: Barco Pages: 155

Brand: Barco Pages: 2

Brand: Barco Pages: 2

BarcoGraphics Maxwell/ 6300

Brand: Barco Pages: 57

Brand: Barco Pages: 5

Brand: NEC Pages: 4

Brand: Barco Pages: 17

Brand: Minolta Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands