background image

3. Installation requirements

3.2

Electrical requirements for the SF-10V display

Power requirements

One SF-10V tile requires 220-240 VAC, 50-60 Hz, 4.32 amps at 230 VAC. Note that one SF-10V tile correspond with a display surface
of 1,23 m². Power link cables are used to link the power from tile to tile. However, MAXIMUM three (3) tiles, may be connected in
parallel. So, one power source cable has to be provided per three (3) tiles. Every power source cable should be protected by a
circuit breaker or fuses rated 16 A / 250 VAC (15 A / 250 VAC in the USA and Canada).

Barco provides a range of power boxes, which meet the requirements of your SF-10V display. Contact Barco
for more information about power boxes and power requirements for your SF-10V display.

Power system

It is recommended to use a TN-S power distribution system (a power distribution system with a separate neutral and grounding
conductor) in order to avoid large ground current loops due to voltage differences in the neutral conductor. The total electrical
installation should be protected by an appropriately rated disconnect switch, circuit breakers, over voltage protector and Ground Fault
Current Interrupters. The installation shall be done according to the local electrical installation codes. In Europe special attention
should be given to EN 60364, the standard for electrical installation of buildings. In Germany VDE 0100 should be adhered to. In
America, special attention should be given to the National Electrical Code, ANSI/NFPA 70.

This equipment MUST be earthed

In order to protect against risk of electric shock, the installation should be properly grounded. Defeating the purpose of the grounding
type plug will expose you to the risk of electric shock.

R59770542 SF-10V DISPLAY 03/12/2010

13

Summary of Contents for SF-10V


















































Reviews: