![background image](http://html1.mh-extra.com/html/barco/s3-series/s3-series_user-manual_3891629244.webp)
7. System Setup
7.16 Con
fi
guration Menu > Add Aux Destinations
General
In this procedure, you will Add Aux Destinations from the de
fi
ned outputs.
Prerequisite
•
Ensure that you are familiar with the
Con
fi
guration Menu
. For details on this menu, please refer to chapter "Con
If more than one Aux Destination is utilized, repeat the below steps until all Destinations are added.
Add Aux Destinations
1. Click on the
Destination
tab to de
fi
ne destinations for the de
fi
ned outputs.
2. From the diagram area click on the output that you want to be part of the destination.
3. Click on the
+Add Aux Destination
blue button to assign the output to the Aux destination.
4. When the destination is created a box appears next to the E2 diagram.
(Optional) Edit the Name
1. Double click on “Destination1” in the Name list to edit the name.
2. When the area turns blue, click the eraser icon to clear the
fi
eld.
3. Type a new name and hit enter when done.
(Optional) Adjust Destination Parameters
Click on the “Adjust” tab that is located on the top. In this Tab there are three sub tabs: Assign, Output and Wide (See below).
(Optional) Adjust Destination Parameters part 1 > Assign Tab
From this menu you can:
1. Edit the name.
2. Change the Destination from Screen to Aux.
3. Set the dimensions if more than one connector.
4. Delete outputs.
5. Select the Auxiliary Scaling Capacity:
Aux Capacity de
fi
nes how much resolution, or actually LINKs of data can be inserted into the scaler. Standard setting is DL and
refer to Dual Link as in connector capacity while 4K is the same as 4Links it also refer to the total of the 4K resolution that can
be entered. 8L refer to 8 Links of 2K data.
Each of the settings will allow for different size input / still and destination sources from the Input Resource tab covered in the
Programming Section below.
DL = Max 2560 x 1600 or 4095 x 1200
4K = Max 4096 x 2400 or 8192 x 1200
8L = Max 8192 x 2400 or 16384 x 1200
(Optional) Adjust Destination Parameters part 2 > Output Tab
From this menu you can:
1. See the output canvas (raster) size if more than one connector in the connector group used for the Aux
2. Choose more actions in sub tabs:
240
R5905948 EVENT MASTER DEVICES 17/07/2017
Summary of Contents for S3 series
