![background image](http://html1.mh-extra.com/html/barco/r9841020-cine-versum-master/r9841020-cine-versum-master_installation-manual_4236570013.webp)
1. Safety Instructions
Exposing flammable or combustible materials into close proximity of this projector could result in the spontaneous ignition of that
material, resulting in a fire. For this reason, it is absolutely necessary to leave an “exclusion zone” around all external surfaces of the
projector whereby no flammable or combustible materials are present. The exclusion zone must be not less than 40 cm (16”) for all
projectors. The exclusion zone on the lens side must be at least 2m. Do not cover the projector or the lens with any material while
the projector is in operation. Keep flammable and combustible materials away from the projector at all times. Mount the projector
in a well ventilated area away from sources of ignition and out of direct sun light. Never expose the projector to rain or moisture.
In the event of fire, use sand, CO
2
, or dry powder fire extinguishers; never use water on an electrical fire. Always have service
performed on this projector by authorized BARCO service personnel. Always insist on genuine BARCO replacement parts. Never
use non-BARCO replacement parts as they may degrade the safety of this projector.
Slots and Openings
Slots and openings in the cabinet and the sides are provided for ventilation; to ensure reliable operation of the projector and to
protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the
product too close to walls, or other similar surface. This product should never be placed near or over a radiator or heat register. This
projector should not be placed in a built-in installation or enclosure unless proper ventilation is provided.
Projection Room
Projection rooms must be well ventilated or cooled in order to avoid build up of heat around the projector.
1.2.2.2 Safety on Installation
Personal Injury or Property Damage
WARNING: To minimize risks of personal injury or property damage, due electrical shock, fire, energy hazards, mechanical and heat
hazards, Ultraviolet an Infrared energy hazards, and/or chemical hazards this equipment must be installed and/or serviced ONLY
by SERVICE PERSONNEL.
•
If the mains switch is not readily accessible, make sure that the plug on the mains cord or the mains outlet is easily accessible,
or that a general switch is provided in the installation in order to disconnect the mains from the unit.
•
Do not place this projector on an unstable cart, stand, table...etc.
•
To prevent risk of fire or electric shock, do not immerse or expose this appliance in water or other liquids.
•
To prevent the risk of electric shock, do not disassemble this appliance, but always take it to an authorized, trained service
person when service or repair work is required.
•
The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire, electric shock, or injury
to persons.
Projector Damage
If the Air Filters are not regularly cleaned or replaced, the air flow inside the projector could be disrupted, causing overheating.
Overheating may lead to the projector shutting down during operation.
In order to ensure that correct airflow is maintained, and that the projector complies with Electromagnetic Compatibility requirements,
it should always be operated with all of it’s covers in place.
Ensure that nothing can be spilled on, or dropped inside the projector. If this does happen, switch off and unplug the mains supply
immediately. Do not operate the projector again until it has been checked by qualified service personnel.
The projector must always be mounted in a manner which ensures free flow of air into its air inlets and unimpeded evacuation of the
hot air exhausted from its cooling system. Heat sensitive materials should not be placed in the path of the exhausted air.
1.2.2.3 Protection from High Intensity Light Beam and Ultraviolet Radiation
WARNING: Do not stare in the high intensity light beam
Do not look directly in the light beam. Due to the high luminance, damage to eye can happen.
Exposure to UV Radiation
The lamp contained in this product is an intense source of light and heat. One component of the light emitted from this lamp is ultra-
violet light. Potential eye and skin hazards are present when the lamp is energized due to ultraviolet radiation. Avoid unnecessary
exposure. Protect yourself and your employees by making them aware of the hazards and how to protect themselves. Protecting
the skin can be accomplished by wearing tightly woven garments and gloves. Protecting the eyes from UV can be accomplished by
wearing safety glasses that are designed to provide UV protection. In addition to the UV, the visible light from the lamp is intense
and should also be considered when choosing protective eye wear.
Some medications are known to make individuals extra sensitive to UV radiation. The American Conference of Governmental In-
dustrial Hygienists (ACGIH) recommends occupational UV exposure for an-8hour day to be less than 0.1 microwatts per square
centimeters of effective UV radiation. An evaluation of the workplace is advised to assure employees are not exposed to cumulative
radiation levels exceeding these government guidelines.
R5976468 CINE VERSUM SYSTEM 03112003
9
Summary of Contents for R9841020 Cine VERSUM Master
