![background image](http://html1.mh-extra.com/html/barco/r9010100/r9010100_owners-manual_474306047.webp)
4. Getting Started
Common address
Default address. Projector will always execute the command coming from a RCU programmed with that common
address.
Why a projector address ?
As more than one projector can be installed in a room, the separate projector should be separately addressable with an RCU or
computer. Therefor each projector has its own address.
Set up an individual Projector Address.
The set up of a projector address can be done via the software.
Projector controlling.
Every projector requires an individual address between 0 and 255 which can be set in the
Installation
menu.
When the address is set, the projector can be controlled by :
•
RCU for addresses between 0 and 9.
•
computer, e.g. IBM PC (or compatible), Apple MAC, etc. for addresses between 0 and 255.
A projector will respond to a RCU set to the common address ’0’ regardless of what address is set in the projector itself (common
address of projector should also be “0” ).
The RCU is default programmed with address 0 , ’common address’.
If it is necessary to control a speci
fi
c projector, then enter the projector address into the RCU (only when that
address is between 0 and 9). The projector with the corresponding address will listen to that speci
fi
c RCU.
Some projectors may operate in domestic environments where other equipments may listen to the common
address “0” , therefore the common address can also be set to “1”.
4.9.2
Displaying and Programming addresses into the RCU
Displaying the Projector Address on the Screen.
1. Press the
Address
key (recessed key on the RCU) with a pencil.
The projector’s address will be displayed in a ’Text box’
To continue using the RCU with that speci
fi
c address, it is necessary to enter the same address with the
digit buttons (address between 0 and 9) within 5 seconds after pushing the address key. For example : if the
Address key displays projector address 3, then press "3" digit button on the RCU to set the RCU’s address to
match the projector’s address. If the address is not entered within 5 seconds, the RCU returns to its default
address (zero address) and controls then all projectors in the room.
Address 0 (or 1) should always allow communication with the projector since it is a common address.
4.9.3
Displaying and Programming addresses into the rugged remote control
Displaying the Projector Address on the Screen.
1. Press the
Addr
(address) key .
The projector’s address will be displayed in a ’Text box’
Programming the projector address into the rugged remote control
1. Press
Addr
key.
The remote jumps immediately to the address menu.
2. Enter the new address with the numeric keys (number between 1 and 255).
Or,
push the
↑
or
↓
key to
fi
ll out the desired address.
R5976690 XLM H25 25/05/2009
43
Summary of Contents for R9010100
