![background image](http://html1.mh-extra.com/html/barco/ph-series/ph-series_user-and-installation-manual_4202641037.webp)
4. Getting started
-
It may take about 2 minutes for the lamp to light up.
-
The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
-
After the
ON/OFF
key is pressed, the image may
fl
icker before the lamp becomes stable. This is not a product malfunction.
-
The lamp operation becomes stable in 2 minutes after the power is turned on and then the lamp mode selected in the menu
is activated. During the activation, displayed images may be disturbed.
-
The projector starts warming up when the
ON/OFF
key is pressed. During the warm-up process, images may appear dark
and no commands are accepted.
-
Do not cover the lens with the lens cap while the lamp is on.
4. Press the
HOME
key to display the OSD Lite menu and press the
▲
,
►
,
▼
,or
◄
key to select LENS FOCUS, and press the
OK
key.
The
LENS FOCUS
menu appears.
5. Adjust with the
◄
or
►
key to get a
fi
ne picture.
6. Select an input source.
-
Press the
HOME
key to display the OSD Lite menu and press the
OK
key. The
INPUT
menu is displayed. Then press the
▲
,
►
,
▼
,or
◄
key to select the appropriate input source.
-
The projector automatically selects the appropriate signal format. The selected signal format is displayed on the screen.
-
Though it may take some time before an image is displayed on the screen depending on the type of the input signal, such
symptom is not a malfunction.
-
For computer images: Images may not be projected in the correct position, depending on the type of the input signal. In such
a case, use the
AUTO POSITION
function.
-
When VGA (COMPUTER 1) or 5BNC (COMPUTER 2) is chosen as the source, images supplied from the computer may
fl
icker. Use
FINE SYNC
. in the
SIGNAL
menu to reduce
fl
icker, if it occurs. (Fine adjustment)
-
Some images become easier to view when the setting of aspect ratio is changed.
7. Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their speci
fi
ed
sizes.
8. Adjust the position of the projector so that the projector and the screen are perpendicular to each other.
When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle.
9. Press the
HOME
key to display the OSD Lite menu and press the
▲
,
►
,
▼
,or
◄
key to select
LENS ZOOM
, and press the
OK
key.
The
LENS ZOOM
menu appears.
10.Adjust with the
▲
or
▼
key to get an approximate size.
11.Press the
OK
key to display the
LENS SHIFT
menu.
12.Press the
▲
or
▼
key to adjust the vertical position and
◄
or
►
key to adjust the horizontal position of the displayed image.
When the image is not displayed within the screen, adjust the projection angle. In addition, perform the keystone adjustment, if
necessary.
13.Repeat steps 4, 5 and 9 to 12, if necessary.
Focus, zoom and lens shift adjustment is possible in the normal picture mode only.
4.4
Stop projecting images
How to stop
1. Press the
ON/OFF
key.
-
A con
fi
rmation message is displayed.
-
To cancel the procedure, press any key except the ON/OFF key.
2. Press the
ON/OFF
key again.
The lamp goes out and the projector goes into a standby mode. In this standby mode, the STATUS Led blinks red.
3. Wait about 2 and a half minutes for the STATUS Led to be turned on.
-
During this period of 2 and a half minutes in the standby mode, the intake fan and exhaust fan rotate to cool the lamp.
-
The air outlet fans rotate faster as the temperature around the projector rises.
-
Though the fans make loud sounds during cooling, such symptom is not a malfunction.
4. Unplug the power cord from the outlet.
R5905597 PHXX SERIES 20/05/2014
33