background image

7. Important information

7.3

Regulatory compliance information

Indications for use

The NIO 2MP LED Display (MDNC-2221) is intended to be used in displaying and viewing digital images
for review by trained medical practitioners. These devices must not be used in primary image diagnosis in
mammography. Caution (USA): Federal law restricts this device to sale by or on the order of a physician.
(Details & exemptions are in the Code of Federal Regulations Title 21, 801 Part D).

FCC class B

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference re-
ceived, including interference that may cause undesired operation.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This device generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television reception, which can be
determined by turning the device off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the device and receiver.

Connect the device into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Changes or modi

fi

cations not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

Canadian notice

This ISM device complies with Canadian ICES-001.

Cet appareil ISM est conforme à la norme NMB-001 du Canada.

7.4

EMC notice

General information

No speci

fi

c requirement on the use of external cables or other accessories except power supply.

With the installation of the device, use only the delivered power supply or a spare part provided by the
legal manufacturer. Using another can result in a decrease of the immunity level of the device.

Electromagnetic emissions

The NIO 2MP LED Display is intended for use in the electromagnetic environment speci

fi

ed below. The

customer or the user of the NIO 2MP LED Display should assure that it is used in such an environment.

Emissions test

Compliance

Electromagnetic environment –
Guidance

RF emissions

CISPR 11

Group 1

The NIO 2MP LED Display uses
RF energy only for its internal
function. Therefore, its RF
emissions are very low and are
not likely to cause any interference
in nearby electronic equipment.

K5903058 NIO 2MP LED DISPLAY 04/03/2014

33

Summary of Contents for MDNC-2221













































Reviews: