Barco MDCG-5221 Page 47 User Manual Download

Page: 47 / 52

8. Important information

These guidelines may not apply in all situations. Electromagnetic propagation is af-
fected by absorption and re

ection form structures, object and people.

8.5

Explanation of symbols

Symbols on the device

On the device or power supply, you may

nd the following symbols (nonrestrictive list):

Indicates compliance with the Directive 93/42/EEC as Class I device

Indicates compliance with the Directive 93/42/EEC as Class II device

Indicates compliance with Part 15 of the FCC rules (Class A or Class B)

Indicates the device is approved according to the UL regulations

Indicates the device is approved according to the UL regulations for Canada
and US

Indicates the device is approved according to the UL Demko regulations

Indicates the device is approved according to the CCC regulations

Indicates the device is approved according to the VCCI regulations

Indicates the device is approved according to the KC regulations

Indicates the device is approved according to the BSMI regulations

Indicates the device is approved according to the PSE regulations

Indicates the USB connectors on the device

K5902074 CORONIS 5MP LED DISPLAY 19/12/2014

Summary of Contents for MDCG-5221





















































Search results

Summary of Contents for MDCG-5221

Reviews:

Related manuals for MDCG-5221

Brands by name

Popular brands

Barco MDCG-5221, User Manual

Search results

Summary of Contents for MDCG-5221

Reviews:

Related manuals for MDCG-5221

Brands by name

Popular brands