background image

K5902108 /06

Coronis Fusion 4MP / 6MP

25

4.

Select

Enabled/Disabled

as desired and confirm.

4.4 Key indicator lights

About the key indicator lights

By default, after lighting up, the key indicator lights will dim again if no further actions are taken within the
following 5 seconds. However, this behavior can be changed so that the key indicator lights are always on or
always off.

To configure the key indicator lights

1.

Bring up the OSD main menu.

2.

Navigate to the

Configuration > User Interface > Indicator Lights

menu.

3.

Enter the

Keys

submenu.

4.

Select

Automatic/Always On/Always Off

as desired and confirm.

4.5 Power lock function

About the power lock function

By enabling the power lock function, the Coronis Fusion 4MP / 6MP is forced to remain switched on. This
means that it can

t be switched to stand-by mode manually until the power lock function is disabled again.

To enable/disable the power lock function:

1.

Bring up the OSD main menu.

2.

Navigate to the

Configuration > User Interface > Controls

menu.

3.

Enter the

Power Lock

submenu.

4.

Select

Enabled/Disabled

as desired and confirm.

4.6 DPMS mode

About DPMS mode

Enabling the Display Power Management System (DPMS) mode on your display will optimize its diagnostic
lifetime by automatically switching off the backlight when the display is not used for a specified period of time.
By default, DPMS mode is enabled on your display, but it also needs to be activated on your workstation. To
do this, go to the

Power options properties

window of your workstation.

Barco recommends setting DPMS activation after 20 minutes of non-usage.

When DPMS mode is enabled on your display, an additional OSD power saving function becomes
available: hibernate. Please refer to

Hibernate

page 26 for more information on hibernation and

how to enable this function.

To enable/disable DPMS mode on your display:

1.

Bring up the OSD main menu.

2.

Navigate to the

Configuration > Power Management

menu.

3.

Enter the

DPMS Mode

submenu.

4.

Select

Enabled/Disabled

as desired and confirm.

Advanced operation

Summary of Contents for MDCC-4330





























































Reviews: