3
R5913246 /00
FL-FS40 MKII SERIES
1 Safety and environmental information
About
Read this chapter thoroughly before attempting to install or operate the projector.
To prevent personal injury to users or physical damage to the projector while installing and using your projector, ensure that you
understand and follow all safety guidelines, instructions and warnings included in this chapter and this manual.
Clarification of the term FL40 series used in this document
Use in this document of the term, FL40 , means that the content is applicable for the following products:
•
FL40 - WU
•
FL40 - 4K
•
FS40 - WU
•
FS40 - 4K
Defining the FL40 platform
The FL40 series products in general, are all products within the Barco GP5 platform
1.1 General considerations
Notice on optical radiation FL40 Series
•
Do not stare into Beam.
•
This projector is Risk Group 2 (RG2) according to IEC EN 62471-5.
•
Any operation or adjustment not specifically instructed by the user
’
s guide creates the risk of hazardous light radiation exposure.
•
Do not open or disassemble the projector as this may cause danger to unauthorized personnel
General safety instructions
•
This product contains no user serviceable parts.
Attempts to modify/replace mechanics or electronics inside the housing or compartments will violate any warranties and may be
hazardous.
•
Do not stare into beam when the projector is on. The bright light may result in permanent eye damage.
•
Before operating this equipment please read this manual thoroughly and retain it for future reference.
•
Installation and preliminary adjustments should be performed by properly trained and qualified personnel.
•
All warnings on the projector and in the documentation manuals must be adhered to.
•
All instructions for operating and use of this equipment must be followed precisely.
•
All local installation codes should be adhered to.
Notice on safety
This equipment is built in accordance with the requirements of the international safety standards IEC60950-1, as basis for National safety
regulation world wide. The safety standard covers information technology equipment including electrical business equipment intended to
operate in
“
normal
”
environments (offices and homes). This safety standard imposes important requirements on the use of safety critical
components, materials and insulation, in order to protect the user or operator against risk of electric shock and energy hazard and having
access to live parts. Safety standards also impose limits to the internal and external temperature rises, radiation levels, mechanical
stability and strength, enclosure construction and protection against the risk of fire. Simulated single fault condition testing reduce the risk
of hazards and contribute to ensure the safety of the equipment to the user even when the equipment
’
s normal operation fails.
Users definition
Throughout this manual, the term SERVICE PERSONNEL refers to Barco authorized persons having appropriate technical training and
experience necessary to be knowledgeable of potential hazards to which they are exposed (including, but not limited to HIGH VOLTAGE
ELECTRIC and ELECTRONIC CIRCUITRY and HIGH BRIGHTNESS PROJECTORS) in performing a task, and of measures to minimize
the potential risk to themselves or other persons. Only Barco authorized SERVICE PERSONNEL, knowledgeable of such risks, are
allowed to perform service functions inside the product enclosure. The term USER and OPERATOR refers to any person other than
SERVICE PERSONNEL.
1.2 Important safety instructions
To prevent the risk of electrical shock
•
This product should be operated from a mono phase AC power source.
•
This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If none of the supplied power cables are the
correct one, consult your dealer.
If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of
the grounding-type plug.
Never use 2- wire power cords, as this is dangerous and could lead to electrical shock. Always use a power connector with a ground
terminal.
•
Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect the
cord, pull it out by the plug. Never pull the cord itself.
•
Ensure that the main power cord complies with the national regulations at the site where the equipment is used.
•
Do not use unauthorized replacements
•
Do not operate the projector with a damaged cord. Replace the cord.
