![background image](http://html1.mh-extra.com/html/barco/f90-series/f90-series_service-manual_3951732037.webp)
8. Thermal management system
8.2
Liquid Cooling Pumps
Article no. / Description 502-0372-xx Liquid Cooler
The primary cooling system comprises
fi
ve (5) liquid cooling pumps, four for the general system and one speci
fi
cally for DMD cooling.
8.3
Fans
RPM control of each fan is tightly enforced by the system processor via FPGA, and will adapt RPM based on the temperature
differential between air inlet and air outlet at any given time. Fan speed can be affected by the mode the projector is running in
(e.g. Quiet mode). To maximize lifetime and minimize stress on critical components, the fan system runs idle when the projector is
in standby (projector is shut off, but power is applied). If a fan operates outside normal parameters (+/- 200 rpm) for more than 2
minutes, the system will shut down and status LED will indicate thermal failure (red
fl
ash). After toggling mains power, the system
may be restarted and fan monitor (in service menu) activated to properly identify which fan is inoperative or operating outside nominal
values. All nominal RPM values are recorded in Desktop mode.
Refer to Chapter 8.6 System Thermal Diagram for details regarding data for the fans.
8.3.1
Fan Radiator
Fan Radiator 1, 2, 3, 4, 5, Driver are all axial-
fl
ow fans which operate by increasing the pressure of air
fl
owing through it.
There are six (6) axial fans (119x25.5) in the system: 5 pcs for the radiators, and 1 pcs for the DMD.
Part Number
Description
Approx. Nominal RPM (25degC, 0m asl)
504-0623-xx
Fan 119x25 24V PWM
2160
8.3.2
Fan Laser Driver
The 60x25 Fan is an axial fan which pulls air from the rest of the system cooling the laser driver, located close to the DLP engine.
Connects to PCB Main, and controlled from system processor.
Part Number
Description
Approx. Nominal RPM (25degC, 0m asl)
504-0623-xx
Fan 119x25 24V PWM
2670
8.3.3
Fan PSU
Radial Fan pulls air from the rest of the system and in to the PSU. Located at the short end of the PSU
Part Number
Description
Approx. Nominal RPM (25degC, 0m asl)
535—0005–xx
Fan Blower 126x127x31
1475
8.3.4
Fan Phosphor Internal 1, 2
Phosphor fans are located inside the PW environment, and can be accessed by removing the PW assy.
Part Number
Description
Approx. Nominal RPM (25degC, 0m asl)
504–0544–00
380 Fan Lamp
4000
8.3.5
Fan PCB Main
Located at the front end of the PSU
Part Number
Description
Approx. Nominal RPM (25degC, 0m asl)
504-0624-xx
Fan Blower 126x127x31
1500
8.3.6
Fan Optics
Located in the front bottom of the projector
Part Number
Description
Approx. Nominal RPM (25degC, 0m asl)
504-0625-xx
Fan Radial Optics 138x42, 3
3000
723–0016 F90 01/12/2017
35
Summary of Contents for F90 series
