![background image](http://html1.mh-extra.com/html/barco/dp2k-slp-series/dp2k-slp-series_user-and-installation-manual_474005081.webp)
7. ICMP
7.13 ICMP reset
This procedure requires that ICMP version 1.2.4 or later is installed.
ICMP reset possibilities
•
The Star button on the local keypad (Not for C- and B-series)
•
The ICMP reset button in the GUI of the Communicator.
•
The ICMP reset button in the GUI of the Commander.
•
The ICMP reset button in the GUI of the Web Commander.
•
The ICMP hardware reset button located on the front panel of the ICMP (Not recommended, use only when all other reset
possibilities are exhausted!)
How to reset the ICMP?
1. Click on the ICMP
reset button
in the GUI of the
Web Commander
Or,
Click on the ICMP
reset button
in the GUI of the
Commander
Note:
It can be that the Commander or WEB-Commander is not able to send the reset command.
Or,
click on the ICMP
reset button
in the GUI of the
Communicator
(recommended)
Or,
press the
Star button
on the
local keypad
for a few seconds (Not for C- and B-series)
As a result the projector is safely prepared for the ICMP reboot. All ongoing events on the ICMP (e.g. ingest) are requested to
end. After a few seconds the ICMP is requested to restart. The READY LED on the front panel of the ICMP starts to blink orange.
In case the ICMP is installed in DP4K-L series projector the lasers are switched off and the projector remains in the same mode
(e.g. Conditioned). The Star button on the local keypad starts blinking green. After the reset of the ICMP the lasers are switched
on again.
Once the READY LED lit continuous green the ICMP is up and running.
2. Did the reset of the ICMP fail?
If yes, perform a hardware reset as follows:
a) switch off the lasers of the projector or switch of the projector lamp.
b) press the ICMP
hardware reset button
a few seconds (reference 3 image 7-13) .
Warning:
Resetting the ICMP with the hardware reset button may cause damage to the content on the HDDs. A re-con
fi
gu-
ration of the whole system may be required!
As a result the projector is safely prepared for the ICMP reboot. All ongoing events on the ICMP (e.g. ingest) are stopped
immediately and the ICMP restarts.
3
Image 7-13
W
ARNING
:
Resetting the ICMP with the hardware reset button may cause damage to the content on the HDDs.
A re-con
fi
guration of the whole system may be required!
R5906847 DP2K SLP SERIES 02/06/2017
77
Summary of Contents for DP2K SLP Series
