background image

1. Safety

Label image

Label description

Label location

WARNING! DO NOT LOOK INTO THE LIGHT BEAM
NO DIRECT EYE EXPOSURE TO THE BEAN IS
PERMITTED

RG3 IEC EN 62471–5:2015

CLASS 1 IEC EN 60825–1:2014

HAZARD DISTANCE: CONSULT SAFETY MANUAL

COMPLIES WITH 21 CFR 1040 EXCEPT WITH
RESPECT TO THOSE CHARACTERISTICS
AUTHORIZED BY VARIANCE NUMBER 2014-V-0285
DATED APRIL 14, 2016 RISK GROUP 3 LIP IEC
62471:2016

警告!

看光束

眼睛勿直接接触可允

暴露的光束

(RG3 IEC EN 62471-5:2015 CLASS 1 IEC EN
60825-1:2014)

危害距离:

参考

安全手册

DANGER !

NE PAS REGARDER LE FAISCEAU EVITER TOUTE
EXPOSITION DIRECTE DES YEUX AU FAISCEAU

RG3 IEC EN 62471-5:2015

CLASS 1 IEC EN 60825-1:2014

DISTANCE DE SECURITE : CONSULTER LE MANUEL
DE SECURITE

Hazard RG3: not for household use symbol

1.4

High Brightness precautions: Hazard Distance (HD)

HD

Hazard Distance (HD) is the distance measured from the projection lens at which the intensity or the energy per surface
unit becomes lower than the applicable exposure limit on the cornea or on the skin. The light beam is considered (to
be) unsafe for exposure if the distance from a person to the light source is less than the HD.

Restriction Zone (RZ) based on the HD

The HD depends on the amount of lumens produced by the projector and the type of lens installed. See next chapter"HD in function
of modifying optics", page 9 
.

To protect untrained end users (as cinema visitors) the installation shall comply with the following installation requirements: Oper-
ators shall control access to the beam within the hazard distance or install the product at the height that will prevent spectators’
eyes from being in the hazard distance. Radiation levels in excess of the limits will not be permitted at any point less than 2.0 (SH
image 1-1) meters above any surface upon which persons other than operators, performers, or employees are permitted to stand
or less than 1,0 (SH image 1-1) meters lateral separation from any place where such persons are permitted to be. In non-cinema
environments where unrestrained behavior is reasonably foreseeable, the minimum separation height should be greater than or
equal to 3,0 m to prevent potential exposure, for example by an individual sitting on another individual’s shoulders, within the HD.

These values are minimum values and are based on the guidance provided in IEC 62471-5:2015 section 6.6.5.

The end user must understand the risk and apply protective measures based upon the hazard distance as indicated on the label and
in the user information. Installation method, barriers, detection system or other applicable control measure shall prevent hazardous
eye access to the radiation within the hazard distance.

6

R5906714 DP2K CLP SERIES 09/05/2016

Summary of Contents for DP2K CLP series












Reviews: