100 - 240 VAC
50 – 60 Hz, 1.9A
ETHERNET
Model
DCS-200
SERIAL
Input 1
Input 2
Input 3
Input 4
Input 5
Input 6
Input 7
Input 8
HD/SD SDI
VIDEO INPUTS
MAIN OUTPUTS
PREVIEW OUTPUTS
* Breakout Cables for Analog Inputs
Menu Tree
— only top level functions are shown
Status Menu
•
Input Type
— Specifies the type of input signal
currently on Program.
•
Input Format
— Indicates video format on
Program. If the input is not valid, “Invalid Signal”
is shown.
•
Next Input Type
— Indicates next Program input
type, plus HDCP status (if applicable).
•
Next Input Format
— Indicates next Program
input format.
Sample Status Menu
Quick Start Guide
Barco Media and Entertainment
11101 Trade Center Drive
Rancho Cordova, CA
95670 • USA
AC
Connect to
AC power
source.
IMPORTANT
Use this table to
connect various source
formats to the DCS-200,
using the system’s
analog input connectors
(
Inputs 1 - 6
).
P/N 26-0604014-00 Rev 00
For complete details on
all installation, setup,
and operating
procedures, refer to the
DCS-200 User’s Guide
.
Program Input Type
Program Input Format
Next Input Type
Next Input Format
Visibly yours
Toll Free:
Fax:
Technical Support:
Website:
+1 (888) 414-7226
+1 (916) 859-2515
+1 (866) 374-7878
www.barco.com
Analog Inputs
Connect to analog sources such
as PCs, VTRs, and cameras.
Use breakout cables as required.
See * below for details.
DVI-I Inputs
Connect to DVI or analog sources.
The connector’s analog pins can be
accessed with a breakout cable, or
a DVI to HD-15 adapter.
HD/SD SDI Input
Connect to SD-SDI or
HD-SDI source.
Program Outputs
1 x DVI, 1 x Analog
provided. Both have the
same resolution, and both
can be used simultaneously.
Communications
Ethernet and Serial connectors are provided for
communications with DCS-200. Use the
Ethernet Menu
and
Serial Setup Menu
to set
parameters. Use
Ethernet
connector to run
web-based GUI.
P R O G R A M :
N E X T :
R G B
1 0 2 4 x 7 6 8 @ 5 9 . 9 4
S D I
N T S C ( 4 8 0 i )
NOTE
•
To display the
Setup Menu
from the
Status Menu
, press
SEL
.
•
To return to the
Status Menu
from
any point in the
Setup Menu
, press
ESC
repeatedly.
Breakout Cable
Wire Color
Comp
Video
S-Video
(Y/C)
YUV
(YPbPr)
RGB
Sync on Green
RGB
Comp Sync
RGB
Separate H V
R
G
B
H Sync
V Sync
(Pr)
(Lum)
(Lum)
(Pb)
If “
HDCP Violation
” appears, an HDCP
source is selected, but a non-HDCP
compliant display device has been
detected. Video output is disabled.
Preview Outputs
Connect to DVI or
analog preview
monitor.
(Chrom)
Recall Config
Status Menu
Tech Support
Factory Reset
Output Format
Gamma
Test Pattern
Sync Setup
Auto Input Save
Black Auto Take
Key Auto Take
Output
Version
Save Config
Key Setup
LOGO Setup
Input
Clip
Gain
Opacity
H Offset
V Offset
Selection
Save LOGO
Delete LOGO
Phone
Setup Menu
In Auto Acquire
Menu Context
Auto Input Cfg
User Preference
Trans Time
Status
System
VFD Brightness
Ethernet
EDID
Save State
DVI Cable EQ
Executive Mode
Diagnostics
Serial Setup
File Association
Input Format
Input
Type
Colorspace
**Image Adjust
Contrast
Brightness
Color Balance
Processing
Save Config
Reset Config
Delete Config
Background
Temperature
Preview
Output Src
Sync Setup
Output Format
Test Pattern
Save
Adjust On
Auto Take
* Use
Timing Adjust
for analog input
sources
except
NTSC and PAL.
** Use
Image Adjust
for DVI, SDI, NTSC
and PAL input sources.
*Timing Adjust
