Connecting A Liquid Propane (LP) Gas Tank To Your Grill
1.
You will need to install the special fitting 3/8"FF (Female
Flare) x 3/8"MF (Male Flare) onto the outlet manifold so
that it is easier to attach the Hose and Regulator (see
Pg.7, Fig.7). Attach LP Hose & Regulator assembly to
the fitting and ensure that both connections are gas tight
(Do NOT use Pipe Sealant on these flare connections).
2.
Open the left door. Pull out the LPG tank drawer. Place
the 20 Ib cylinder with foot ring into the hole in the draw-
er. See
Figure 16.
Make sure the tank valve is in the
OFF position. Make sure the gas tank is in the upright
position. Use the 5/16” x 90mm wing bolt provided to
secure gas tank.
3.
Check the tank valve to ensure it has proper external
mating threads to fit the hose & regulator assembly pro-
vided. See
Figure 17.
(Type 1 connection per ANSI
Z21.58a-1998)
4.
Make sure all burner valves are in the OFF position.
5.
Inspect the valve connection port and regulator assembly.
Look for damage or debris. Remove any debris. Inspect
hose for damage. Never use damaged or plugged equip-
ment.
6.
When connecting the hose and regulator assembly to the
tank valve, hand tighten nut clockwise to a full stop. Do
not use a wrench to tighten because it could damage the
Quick Coupling Nut and result in a hazardous condition.
7.
Open the tank valve fully (counterclockwise). Use a
soapy water solution to check all connections for leaks
before attempting to light your grill. See ”Checking for
Gas Leaks” on page 14. If a leak is found, turn the tank
valve off and do not use your grill until the leak is
repaired.
Disconnecting An LP Gas Tank From Your Grill.
1.
Turn the burner valves and LP gas tank valve to the full
OFF position. (Turn clockwise to close.)
2.
Detach the hose and regulator assembly from the LP
gas tank valve by turning the Quick Coupling Nut coun-
terclockwise.
CAUTION: When the appliance is not in use, the gas
must be turned off at the supply tank.
Connecting Natural Gas To Your Grill
1.
You will need to install the Special fitting as follows:
3/8” FF x 1/2” MP for Y0665
1/2” FF x 1/2” MP for Y0662 & Y0663
Connect from the outlet manifold to the 12ft. Hose and
QD(Quick Disconnect) on cart model or the Natural Gas
Regulator to stainless steel flexline & shut-off valve for
built-in installation.
2a.
Built-in Model: Install the Shutoff Valve, Close Nipple,
Stainless Steel Flexline to the Natural Gas Regulator.
The Shutoff Valve must be intalled directly to the outlet
pipe and the Natural Gas Regulator must be connect
directly to the outlet manifold.
2b.
Cart model: Pass the hose through the hole in the cart
and connect the 12ft hose directly to the Natural Gas
Regulator. Make sure you have installed a Shutoff
Valve on the supply line.
3.
Turn the gas supply on and fully open the shutoff valve.
Use a soapy water solution to check all connections for
leaks before attempting to light your grill. See ”Checking
for Gas Leaks” on page 14. If a leak is found, turn the
gas supply off and do not use your grill until the leak is
repaired.
Figure 16
GAS
TANK
TANK
DRAWER
WING BOLT
Models Y0662
and Y0663
Figure 17
GAS
TANK
TANK
DRAWER
QUICK CONNECT
COUPLING NUT
Type 1 connection
per ANSI Z21.58a-
1998
Congratulations
Your Barbeques Galore gas grill is now ready for use.
Before the first use and at the beginning of each season
(and whenever the LP gas tank has been changed):
1.
Read all safety, lighting and operating instructions.
2.
Check gas valve orifices, burner tubes and burner
ports for any obstructions.
3.
Perform gas leak check according to instructions
found on page 14 of this manual.
- 13 -
