OB Burners – Unpacking and Setup – Millivolt Valve Systems
STEP 1 (For OB72 & OB96 only):
Connect Burners using [2] 10-24 x
1/2” bolts. Set Cover Clip over joined
burner ends.
STEP 2:
Insert Orifice(s)
into mixing sleeve(s) and
install bracket(s) with [4]
1/2” DT Screws. Then
insert Pilot Assembly into
one Burner and attach with
[2] 1/2” DT Screws.
Attach Pilot Opening Cover
in the other Burner with [2]
1/2”DT Screws.
Air Shutter = 1/16”- NG
Air Shutter = Full Open- LP
STEP 3:
Install Burner with attached Valve System into structure.
For Outdoor Fire Tables (OFT) refer to
OFT Burner Installation Instructions
page.
For Outdoor Fireplaces (OFP) refer to
OFP
Burner Installation Instructions
page.
For Custom Enclosures refer to
Custom Enclosures
Section.
NOTE:
Filler Strips must be installed before media is placed into burner.
Parts List: OB72 / OB96MVN
[2] Burners, c/w [2] Pilot Shields, [2] Ends, [6] Filler Strips
[1] Millivolt Valve
System (c/w [2] Orifice Assemblies and [1] Pilot
Assembly)
[1] Piezo Button Igniter c/w wire and Sparker
[1] On/Off Rocker Switch (installed on valve)
[1] Pilot Opening Cover
[1] Hardware Bag: [12] 1/2” DT Screws, [8] #6 Black Screws, [2]
10-24 x 1/2” Bolts c/w Star Nuts
[6] Filler Strips
[1] Cover Clip
24OB – 23-9/16”
36OB – 35-9/16” (x 2 for OB72)
48OB – 47-9/16” (x 2 for OB96)
24OB – 10-5/8”
36OB – 10-5/8” (x 2 for OB72)
48OB – 10-5/8” (x 2 for OB96)
24OB – 10-5/8”
36OB – 22-5/8” (x 2 for OB72)
48OB – 34-5/8” (x 2 for OB96)
Connect Electrode
Wire to Piezo.
Connect On/Off
Switch to
TP
and
TH
Terminals
.
Connect Electrode Wire to
Piezo.
Connect On/Off Switch to
TP
and
TH
Terminals.
Install Pilot Assembly and
Orifice Bracket [4 Dt Screws].
Cover Clip
Pilot Assembly
is
installed from
bottom of Burner
Tray – but
can be
serviced from the
Top
.
Parts List: OB24 / OB36 / OB48MVN
[1] Burner, c/w [1] Pilot Shield, [2] Ends, [3] Filler Strips
[1] Millivolt Valve System (c/w Orifice Assembly and Pilot Assembly)
[1] Piezo Button Igniter c/w wire and Sparker
[1] On/Off Rocker Switch (Installed on valve)
[1] Hardware Bag: [8] 1/2” DT Screws, [4] #6 Black Screws
[3] Filler Strips (See Below)
Orifice
Retainer
Bracket
Pilot Opening
Cover
FILLER STRIPS:
[Qty 4] 1/2”
DT Screws
to attach
valve to
appliance
Long Flange Up
Short Flange
Down
[Qty 2] 1/2”
DT Screws
[Qty 2] 1/2”
DT Screws
11
