background image

Baracoda IDBlue – User Guide v2.4.2 

 

- 13 - 

8.

 

Safety / Regulatory 

 

FCC: 

Product FCC Id: 

SW4IBRF001LBT 

Interference statement: 

This device complies with Part 15 (class C) of the FCC Rules. 

Operation is subject to the following two conditions: 

(1) this device may not cause harmful interference, and  

(2)  this  device  must  accept  any  interference  received,  including  interference  that  may  cause  undesired 

operation. 

 

Modification statement: 

The  FCC  requires  the  user  to  be  notified  that  any  changes  or  modifications  made  to  this  device  that  are  not 

expressly approved by Baracoda Wireless Technology, may void the user’s authority to operate the equipment. 

 

Wireless notice 

This product emits radio frequency energy, but the radiated output power of this device is far below the FCC 

radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential 

for human contact with the antenna during normal operation is minimized. The system antenna(s) used for this 

transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 

 

 

 

 

 

 

 

 

 

Data Capture 

for Workforce 

in Motion 

All manuals and user guides at all-guides.com

Summary of Contents for IDBlue















Reviews: