BAPI VOC Installation And Operating Instructions Manual Download Page 4

Installation and Operating Instructions

VOC Room Sensor in the BAPI-Stat 3 Enclosure 

with Differential Ground Configuration

Building Automation Products, Inc., 750 North Royal Avenue, Gays Mills, WI  54631 USA

Tel:+1-608-735-4800 • Fax+1-608-735-4804 • E-mail:[email protected] • Web:www.bapihvac.com

Specifications subject to change without notice.

29156_ins_voc_room_dif_gnd

4 of 8

rev. 06/05/18

Wire Color

Ground

Black

Tip

White

Ring

Red

Table 1: C35 Wiring

  

Optional Communication Jack Wiring

Fig 5: 

Communication Jack

C35

C35 Communication Jack

(Male jack shown for clarity)

  

User Operation

BAPI Man Icon

Minor Display 0.34” 3-digit Alpha-Numeric

Main Display 0.76” 4-digit Numeric 

Fig 6: 

Optional Display

Optional VOC Level “Arrow” Indicator  

(-ARW Option)

ON Icon for 

Verification and 

Commissioning

The display indicates VOC in PPM, air temperature in degrees Fahrenheit or Celsius, relative humidity in %RH, 

temperature setpoint in degrees Fahrenheit or Celsius and override using the BAPI Man icon.  The three arrow 

icons are used with the –ARW option to show VOC levels and their meaning.
The main display indicates the numeric value of the quantity being displayed.  The minor display indicates the 

engineering units of the value, such as VOC, °F, °C or %RH.

Temperature Setpoint Slide Pot:

 

Moving the slide pot enough to change the setpoint by one degree 

will display the setpoint on the main display if equipped with display. 

The setpoint display will hold for five seconds after moving the slide 

pot.

Override Button:

 

When the override button is pressed on display units, the BAPI Man 

icon will display.  A dry resistance of less than 1 Ohm appears from 

the override output (OVR) to the Ground terminal (GND).  Latching 

the BAPI Man icon to show that the system is in override requires 

that a dry contact on your controller be used to connect terminal 

EXT to ground.

Optional VOC Level Indication via Arrow or 3-Color LED

 (Fig. 7)

VOC level indication is available via a black arrow on the display or 

a three-color LED on the logo plate with green for good, yellow for 

fair and red for poor.

Fig 7: 

VOC Level Indicators

Arrow 

Indicators 

& Legend

LED

Indicator & 

Legend

Note:

 Both 

indicators are 

not available 

together

Summary of Contents for VOC









Reviews: