Fig. A2
Fig. A1
Fig. A3
Fig. A4
Fig. A5
Fig. A6
90328 Banzai
3
safety area
10 ft (305 cm)
10 ft (305 cm)
PLACEMENTS: Use on flat lawn only, not pavement or other hard surfaces. Lawn should be free
of rocks, bumps, depressions, sticks, etc. The product should be set up in a location that has a
minimum distance of 10 ft (305 cm) from any freestanding structures or obstructions, including
houses, garages, fences, trees, playground equipment and large rocks.
WARNING:
Overfilling will cause damage to your ball.
This product is intended to be used as a toy
and not as a personal flotation device.
Inflate this product with AIR.
NOTE: For easy air inflation, use
a manual air pump designed
specifically for plastic inflatables.
SETUP
You don’t need a surfboard to ride the Pipeline—just take a deep breath, push off down the slide
and yell, “Banzai!” You’ll race down the cushiony slick slide and through a wall of water before
landing with a giant splash. With the included continuous airflow blower, all of this fun inflates in
under 2 minutes. Heavy-duty Dura-Tech™ construction ensures lasting strength and durability.
So unroll, inflate, add water and have fun!
INTRODUCTION
SETUP INSTRUCTIONS
OR
OR
Fig. A12
Fig. A7
Fig. A8
Fig. A9
Fig. A10
Fig. A11
1. Unfold the constant air inflatable and place in the desired position on a smooth and level surface.
2. Lay out the water hose assembly and match the number on each sprayer to the correct position on the
arch of the inflatable. Once the numbers are matched, attach the sprayers to the arch and
corresponding position using the Velcro straps provided. Secure the water tubing using the Velcro hooks
& loops located on top of the arch, and along the side of the inflatable. (Fig A1-A3)
3. Attach the long intake tube at the back of the inflatable to the mouth of the blower motor using the
attached Velcro strap. To ensure a secure fit, wrap the strap around the mouth of the blower and tightly
attach the self-sticking strap. (Fig A4-A6)
4. Use the drawstrings to tie shut the short air release tube along the back of the constant air inflatable.
(Fig A7)
5. Position the blower in a straight line
perpendicular and level to the back of
the inflatable. The blower should be
placed on a stable surface and
remain upright after the inflatable is
inflated. The blower is a high-volume
fan capable of moving a lot of air very
quickly. Place the blower in an area
where it will not suck in dirt or leaves.
Keep blower away from children,
water and moving vehicles. Set up the
inflatable far away from any structures or obstructions. Once positioned, secure the blower with the
blower ground stakes provided.(Fig A8)
6. Do not set up over concrete, asphalt, packed earth, or any other hard surfaces. A fall onto a hard
surface can result in serious injury.
7. Locate the loops around the bottom of the inflatable and anchor them to the turf, sand soil or rock soil
with the water slide ground stakes provided. (Fig A9)
8. Ground stakes must be completely inserted into the ground so that no part of the stake is protruding
above the ground surface. This will help prevent tripping or injuries resulting from a fall.
9. Plug the blower into a properly grounded outlet and turn it on. The inflatable should inflate in under 2
minutes. Do not allow children to use the inflatable until it is fully inflated.
10. Close the water valve at the bottom of the pool. (Fig A10)
11. Fill the pool with at least 8in (20cm) of water before playing. Thoroughly wet all slide surfaces, platforms
and climbing walls before use to ensure optimal play performance.
12. Do not fill the product tub to more than the maximum fill line marked inside the pool wall.
13. After inflation, the blower should run continuously while children are playing.
FOR INFLATABLE BASKETBALL:
14. Roll out the ball. Inspect for holes, tears or other damage. (Fig A11)
15. Inflate this product with AIR. (Fig A12)
NOTE:
For easy air inflation, use a manual air pump designed specifically for plastic inflatables.
BY MOUTH: Remove the air valve plug and squeeze the base of the valve causing the inner flap to
open for inflation.
BY PUMP: Remove the air valve plug and insert air pump nozzle into the valve. The air pump nozzle
should be inserted deep enough to open the inner valve flap.
Do not over inflate the item. Once the item is completely inflated, then insert the air valve plug to seal it
shut.
NOTE:
Fill inflatable with air until it is firm and solid. If there is any straining at the seams, the item is
over inflated. If any seam begins to strain, immediately stop inflation and release air to reduce the
pressure until all signs of stress on the inflatable are gone. DO NOT use the inflatable if there is
straining at the seams. Use of an over-inflated item may result in serious injury, paralysis or death.
Inspect this product for rips, tears or punctures. Do not use if damaged.
