background image

Switch configurable temperature Node with thermocouple/thermistor inputs and two discrete inputs (powered by external battery module

only)

For additional information, updated
documentation, and accessories, re-
fer to Banner Engineering's website, 

www.bannerengineering.com/sure-
cross

.

The SureCross

®

 wireless system is a radio frequency network with integrated I/O that can oper-

ate in most environments and eliminate the need for wiring runs. DX99 wireless networks are
formed around a Gateway, which acts as the wireless network master device, and one or more
Intrinsically Safe Nodes.

• Wireless industrial I/O device with two selectable discrete inputs and up to three configurable

thermocouple inputs (defaults to J-type)

• FlexPower

®

 power input requires power from the DX81H Battery Supply Module

• One thermistor input used for integrated cold junction compensation (CJC)
• DIP switches for user configuration
• Frequency Hopping Spread Spectrum (FHSS) technology and Time Division Multiple Access

(TDMA) control architecture ensure reliable data delivery within the unlicensed Industrial,
Scientific, and Medical (ISM) band

• Transceivers provide bidirectional communication between the Gateway and Node, including

fully acknowledged data transmission

• Lost RF links are detected and relevant outputs set to user-defined conditions
• DX99 Polycarbonate housings are certified for use in Class I, Division 1, Groups A, B, C, D;

and Zone 0 (Category 1G) when properly installed in accordance with the National Electrical
Code, the Canadian Electrical Code, or applicable local codes/regulations

Model

Frequency

I/O

DX99N9X2S2N0T4X0A0

900 MHz ISM Band

Inputs: Two selectable discrete, three thermocouple, one thermistor
(for CJC)

DX99N2X2S2N0T4X0A0

2.4 GHz ISM Band

Internal antenna models are also available. For more information, contact your local Banner Engineering Corp. representative.

WARNING: Not To Be Used for Personnel Protection
Never use this device as a sensing device for personnel protection. Doing so could lead to serious
injury or death.
 This device does not include the self-checking redundant circuitry necessary to allow its
use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-
energized sensor output condition.

SureCross User Configuration Tool

The User Configuration Tool (UCT) offers an easy way to link I/O points in your wire-
less network, view I/O register values graphically, and set system communication pa-
rameters when a host system is not part of the wireless network.
The UCT requires a special USB to RS-485 (model number BWA-UCT-900 for 1 Watt
radios, BWA-HW-006 can be used for all other radios) converter cable to pass infor-
mation between your computer and the Gateway. Download the most recent revi-
sions of the UCT software from Banner Engineering's website: 

http://www.banneren-

gineering.com/wireless

.

Setting Up Your Wireless Network

To set up and install your wireless network, follow these steps.

Disconnect the power from your SureCross devices.

1. Configure the DIP switches of all devices.
2. Connect the sensors to the SureCross devices.

SureCross DX99 FlexPower Thermocouple Node

(Polycarbonate Housing)

 

 

P/N 142498 Rev. E

6/21/2013

0 142498

0

Summary of Contents for SureCross FlexPower DX99 Series









Reviews:

Related manuals for SureCross FlexPower DX99 Series