Banner DX80DR9M-HB1 Manual Download Page 11

at any time. For the most recent version of any documentation, refer to: 

www.bannerengineering.com

©

 2006-2012 Banner Engineering

Corp. All rights reserved.

Antenna Installation

Always install and properly ground a qualified surge suppressor when installing a remote antenna system. Remote antenna configura-
tions installed without surge suppressors invalidate the manufacturer's warranty.
Always keep the ground wire as short as possible and make all ground connections to a single-point ground system to ensure no ground
loops are created. No surge suppressor can absorb all lightning strikes. Do not touch the SureCross

 device or any equipment connec-

ted to the SureCross device during a thunderstorm.

Exporting SureCross Radios

It is our intent to fully comply with all national and regional regulations regarding radio frequency emissions. Customers who want to re-
export this product to a country other than that to which it was sold must ensure the device is approved in the destination
country.
 A list of approved countries appears in the Agency Certifications section of the product manual. The SureCross wireless prod-
ucts were certified for use in these countries using the antenna that ships with the product. When using other antennas, verify you are not
exceeding the transmit power levels allowed by local governing agencies. Consult with Banner Engineering if the destination country is
not on this list.

Banner Engineering Corp Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of
shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned
to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse,
abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (IN-
CLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND
WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL
BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPEN-
SES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY
PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WAR-
RANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or
liabilities relating to any product previously manufactured by Banner Engineering Corp.

 

 

SureCross MultiHop Data Radio Module

 

www.bannerengineering.com - tel: 763-544-3164

 

Summary of Contents for DX80DR9M-HB1












Reviews: